Having problems with your Tristar TTV Turbo Tiger Handheld Vacuum ?

Turbo Tiger bag is worn out. Where can I get a replacement?

Answers :

Try calling 800-558-0420 to order parts or supplies.
Repair Help & Product Troubleshooting for Tristar TTV Turbo Tiger Handheld Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Turbo Tiger bag is worn out. Where can I get a replacement?

Try calling 800-558-0420 to order parts or supplies. ... Tristar TTV Turbo Tiger Handheld Vacuum

Replacement bag for Turbo Tiger

Go to Website below.Vacuum Cleaner Parts, Vacuum Parts, Vacuum Bags, Vacuum Cleaners and Vacuum Cleaner Bags at TotalVac ... Vacuums

Need replacement bag for Turbo Tiger hand held vac

978-777-3700\012This is the phone number. Website below.\012\012Vacuum Cleaner Parts, Vacuum Parts, Vacuum Bags, Vacuum Cleaners and Vacuum Cleaner ... Tristar TTV Turbo Tiger Handheld Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

I just notice when I went to change bag in my Kirby G4 that the whose inside was split open, which made all the dust fill up in the bag. How do I get a replacement part for this and what is that part called. Do I need to buy the whole outer bag?

You do not need a whole bag. The bag fill tube is replaceable. can be temp fixed with duct tape and new one installed at home. vacuum inside with another vac and you will be set to replace ... Kirby G4 Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Getting the vacuum to start after replacing the bag

Behind the door and above where the bag is located there should be a piece of plastic, or metal that sticks out, at least in the manual, if the door isn't shut correctly, that piece doesn't push in the switch that is behind there, this is a safety fe ... Lindhaus Activa 30-38 Bagged Upright Vacuum

I have a canister vacuum. I replaced the bag and now can otn get a good suction. Could it be the rubber seal near the bag?

The case that encloses the bag may not have been closed properly, or a part of the bag got caught in the seal of the case. Take the bag out and reinstall. Hope this helps! ... Vacuums

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers

The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.

... Windsor SR12 Sensor Bagged Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil

Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?

... Bissell Vacuums

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks

... Eureka Bravo II Bagged Upright Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Kirby Heritage II Turbo and I need a user's manual, but can't find one anywhere. I have to replace the fill tube in the bag and can see the cable tie on top that holds it in place, but don't know how it's attached to the mini-emtor. If I can't replace the fill tube, will tape fix it? If I just taped it; will it hold? Thanks.

Taping usually just causes a mess. The mini-emptor has coarse threads on it that the fill tube screws on to. Occasionally there is a cable tie on the bottom which is not really necessary. If you cut the tube near the bottom, you can get hold of it's ... Kirby Heritage II Vacuum

Fan replacement I have to replace the fan on my g4 how do I get the old fan that is worn and broken off the shaft,,thanks for any help that you might be able to give

Detailed instructions on fan replacement HEREGoodLuck,Rocky:-) ... Kirby G4 Bagged Upright Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat

It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Where can I get replacement Polythene roll for Pifco Vacuum Bag Sealer 1101

... Vacuums

Where can I get replacement bags for the Readivac Model 36721 canister vacuum?

We have the bags ReadiVac 36010 ReadiVac Tidy Turbo Vac bags ... Readivac 36721 Canister Vacuum

I have replaced the filters and the bag on my Sebo X1 automatic upright but it still has doggy odor that I cannot seem to get rid of. What could be the cause and what can I do?

Hi, Yeah those things are fairly simple and easy to clean, My guess is that its in the hose.\015\012Try a weak solution of bleach and water, pour it in and let soak for 20 mins then rinse well. Dry it throughly in the sun before youe next use. ... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

How can you purchase bags for z-c-x3200 - Tristar TTV Turbo Tiger Handheld Vacuum

... Tristar TTV Turbo Tiger Handheld Vacuum

U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?

... Hoover U5468-900 WindTunnel Bagged Upright Vacuum

Cant get the suction impellar off to replace - Kirby Generation 3 Bagged Upright Vacuum

Shaft has to be spun clockwise. It has reversed thread. If this is not the problem but you just need to somehow hold the field - see instructions HERE. You may ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1046 seconds