Having problems with your U5209-930 ?
Change belt on beater bar
How do I change the belt on the brush assembly
Repair Help & Product Troubleshooting for U5209-930
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Beater bar The beater bar will not work. I have changed the belt and there is a lot of suction from the hose. Just seems like the base is not turning on
You may have a bad switch, one part of it is not turning on the brush roll motor. It could also be the brush roll motor. ... Clarke CombiVac 12 Bagged Upright Vacuum
Belt how do you change the belt on the beater bar; dyson animal dc 07
Http://video.aol.com/video-detail/dyson-not-picking-up-dirt-no-suction-how-to-repair/2334249387 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a model B1500 vacuum. The vacuum would lug and stop and start if I lifted it off the rug. I changed the belt to the beater bar. That didn't help. I also noticed that the connection between the hose and wand heats up. How can I fix it?
I'm not exactly sure what make of vacuum this is -- a number of companies make a model b1500, so this may be a bit general. If the vacuum has an adjustment for the height of the carpet pile and you have it set too low, it will overload the brush and ... Vacuums
Need to change the belt on my kirby model 519, assuming this is the problem since the beater bar is not turning and I can smell burning rubber
The beater bar is jammed--usually from thread, string, and hair that is wound up on the bar and particularly on the bar end bearings. The bearings themselves usually require cleaning and re-oiling. The belt may be damaged sufficiently to require repl ... Vacuums
How to change the beater bar belt on a electrolux model 1500c
... Electrolux Vacuums
How to open the beater bar to change a belt
Hi There,Here's a very helpful repair solution that I've written explaining how to fix the belt. There are two hidden screws on your machine that need to be removed first, this repair solution will help you figure out where those screws ... Kenmore 24212 Whispertone Bagged Canister Vacuum
Model v 2010 001 how do you remove the beater bar to change the drive belt
... Hoover F7429-900 Upright Steam Cleaner
Changed belt in hoover windtunnel t-series not beater bar wont spin when vacumming
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]
Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Beater bar my beater bar won't go around, checked & the belt is fine. The motor driving the belt isn't working
... Hoover Platinum LiNX Cordless Stick Vacuum
I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile
... Eureka Smartvac 4870 Bagged Upright Vacuum
Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.
Hi there,Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off. If you ha ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Beater Bar Belt Removal from Upright Electrolux Vacuum
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783793\015\012Generic problem for all Vacuums\015\012Beater bar Belt Removal from Upright Electrolux...\015\012 ... Vacuums
Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.
Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?
... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum
My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn
The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums
We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Beater bar not moving. Is there a belt? My mom sucked up a sock and didn't know. So she kept vacumming and then smelled something rubbery burning. And then we found the sock and cleared it. Then the beater bar wouldn't move after that. How do I fix it.
Hello,The belt is broken or badly stretched and needs to be replaced. Here is a link to download a manual.Look for the "Download Manual" on the right side of page. Scroll down towards bottom of page and you'll see how to open it up to cha ... Eureka 4700A Maxima Bagless Upright Vacuum
Beater bar is not coming on- belt is on, canister is empty. Vacuum runs but no beater bar
The small motor inside the housing that runs the belt blew on mine. Twice. I swapped out the motor from my retired bissell and its good to go. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?
Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum
I have a central vac. and the beater bar, for the carpet is not turning. the vacuum still sucks but the beater bar doesn't turn. I checked the belt it is fine.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=818384\015\012Generic problem for all Vacuums\015\012I have a central vac.\015\012Posted by bmiller874 ... Vacuums
I was cleaning the hair from the beater bar, and it popped out with the belt still attached...have tired to put it back in , but the beater bar will not rotate when the vacuum is turned on
When you put it back make sure that the ends of the bar fits exactly in the ends o the box and has to roll smoothly even when you rotate it with your hand when you try this has to be disconnected ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?
You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum