Having problems with your Ultimate G ?
The foot tork to go up and down popped off and the little spring that it has with it came out
So how do I place the spring back in where dose it actually go in that foot tork to go up and down
Repair Help & Product Troubleshooting for Ultimate G
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.
... Panasonic Kenmore Canister Vacuum Vacuum
Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.
I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I took my Dyson DC 25 Animal apart to clean it, and now the red foot pedal won't lock the vacuum into the upright position anymore. The trouble is the spring pin for the pedal popped out and I can't figure out where it is supposed to go.
That spring thing goes where the pedal screws into the side. When 'facing' the dyson in the front, it's on the left side. The spring's circle part and short stem section goes into a divot area on the pedal. The other end is tensioned (braced) a ... Dyson DC25 All Floors Bagless Upright Vacuum
The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?
... Dyson DC25 Animal Bagless Upright Vacuum
Dyson DC-07 Hose Wand Spring Came Out. How to put back in?
You'll see that there is a round piece with a cross shape on the inside of the button wand release button - place the end of the spring over the cross - you'll see the same cross on the collar of the machine...it'll take some doing, but line the othe ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!
... Sharp Twin Energy EC-TU2607 Vacuum
Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o
Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My 9 year old Sebo X4 will not stay in the upright position. The foot pedal no longer springs back to hold the machine in the upright position. Has a spring broken? Which part needs replacing?
... Sebo X4 Bagged Upright Vacuum
Reattach spring Spring from bottom of base that attaches to the back wheel base came off
This is the only picture i can find it may help youhttp://abcvacuumwarehouse.com/stabilizer-assembly-for-dyson-dc25.html ... Dyson DC25 All Floors Bagless Upright Vacuum
My dc 25 stabilizer bar came apart and a spring came out. Its on the right side. I need to know where it goes back in.
... Dyson DC25 All Floors Bagless Upright Vacuum
The Lower body of the Bissell QuickSteamer, water pours out from the body. Solution: I took apart the machine and there is a spring loaded valve with a rubber washer at the bottom. Think of the letter T upside down with the rubber washer on it. The washer stretches over the bottom and the spring creates a leakproof plug and won't allow water to pass till the button on the handle is pressed. This old washer came partially off and allowed water to leak. I purchased from the plumbing dept. a mi
... Bissell Vacuums
The right front wheel came off my G6 Kirby vacuum, then the entire axle and wheel adjustment came loose--including a spring that was attached to something.
Thank heavens for a husband who can fix anything--and save me a lot of money for repairs and advice! ... Kirby Vacuums
When removing the canister bag, the plate and spring that it slides into popped out. When I put them back in, the bag full indicator is completely red. It is a new bag and filters. I think I am not getting the plate and spring back in the canister correctly. Any instructions or pictures showing proper insertion and configuration of these? I looked in the manual and the part is only shown while bag being inserted.
... Miele S514 Solaris Bagged Canister Vacuum
I bought a roomba pro elite robotic floorvac at a tag sale from an elderly couple who apparently used this vac very little as it was very clean and she had never even used it enough to use the extra filters that came with it, she said it was just too much for her to bend down to work it or move it. i suspect she stored it but kept the battery in it. after charging it, it powers up and sings a little tune, but then shuts off. i cleaned everything, including the sensors. it still shuts off, do you
... Roomba Pro Elite Bagless Robotic Vacuum
Found little "O" ring came out of little green machine don't know where.
... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Foot pedal came apart.Trying to reconnect.Might be missing a part.Need a drawing on assembly for foot pedal that operates the shifting from the hose to the floor vac
\012It took some searching but the site you need is called "dyson medic.com" This is the place that will have the repair manual you are looking for. You are not alone in the world of broken dyson's. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.
You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum
I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?
Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums
Sparks came out of the area of the foot switch and
This is now a dangerous appliance and should be repaired by a qualified tec ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Foot operated release "spring" is broken. Replaceable?
... Bissell 3590 CleanView Bagless Upright Vacuum
Release spring popped off when dumping the cannister.
As long as the black piece still has the "nubs" on both sides at the turn in the "L" shape and the base isn't broke then this is going to be easy. There is a groove on the main unit the little wheel fits into that groove, the "nubs" fit into small ho ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Help ok the diagram is helpful but i have a black wire that came loose from somewhere it has a little prong on it does it click back in opposite from the white let me know please
I am not sure what exactly you are referring to but I think that it may be a motor lead. See pictures below (shown is white but second wire to the motor is black) ... Rainbow E series Canister Wet/Dry Vacuum
I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?
Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums