Having problems with your Unknown LAURASTAR PREMIUM S3 Ironing System ?

Iron will not heat up

\015 Iron part does not get hot. water in boiler does not get hot. need a schematic.\015

Answers :

See the causes and proceed according, fix it. God bless you
If the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary.
If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below).
If the iron produces too much or too little heat, test the electrical cord. Also test and, if needed, adjust calibration of the thermostat (see the Appliance Controls Fix-It Guide).

9_23_2012_5_55_00_am.jpg
Repair Help & Product Troubleshooting for Unknown LAURASTAR PREMIUM S3 Ironing System

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to


... Philips Vacuums

I have an IS222 Bernina Steam Iron that quit steaming today---the iron heats up but the steam switch doesn't light or heat. It appears that we needs a new steam switch. Can you furnish this?


... Vacuums

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

Conair does not sell the springs for their curling iron. Mine keep breaking and I do not want to keep buying a whole new curling iron just because the wire spring has broken. Instant Heat curling iron, model number CD8sWCS. Do you know where I can buy these springs or how I can improvise with something that will work almost as well?


Hi,\015\012\015\012The best thing I know of is to take a wire bread bag tie....take the paper off of it so that you just have the wire part... twist this around the two ends of the wires where it broke...this will contect the two wires an ... Conair Vacuums

My breville steam generator iron heats up but doesn't steam. I have only ironed 5 clothes with it.


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Euro-pro iron. red light on. green light blinks on but iron will not heat up. lights do not progress through yellow (does not go past green) purchased from walmart with warranty extention on 12/08. Never had a problem before--what is wrong.


The inner grid that heats up the iron has an open which will not give continuity to heat the iron up. These grids are not serviced so more than likely a replacement iron will be on your list to purchase ... Vacuums

I have a shark iron model G1495N It has a cut in the wire inside the rubber hosing that goes around the cord from the base of the iron When using it yesterday I didn't see the cut and it sparked after plugging it in and heating up Is not usable at all What can I do to repair it if at all? I've had it since sept 2008 Thnxs


It's probably best to replace the device, when dealing with sparks and exposed wires. \015\012\015\012If you're electrically-inclined, feel free to pry it apart (when unplugged!) and see if you can re-attach things, but generally soldering or g ... Vacuums

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums

Iron will not heat up, used it yesterday, and today it gives no heat!


Hi,Here is a tip that I wrote about Electric Irons and why they do not heat....Electric Ironnot Heating Up or not Working Right\012heatman101 ... Vacuums

Iron will not heat up


See the causes and proceed according, fix it. God bless youIf the iron doesn't heat, make sure power is on to the outlet, check the electric ... Unknown LAURASTAR PREMIUM S3 Ironing System

Got russell hobbs slipstream iron, was useing it when suddely stopped working.dont seem to heat up.and no steam coming out.please advise what to do.model no 14863. thank you.


Check plug/electrics fuse okay, could be stat or heating element ... Vacuums

My steamworks signature iron won't heat up - Vacuums


... Vacuums

On turning the power on , bright light indicator (above the themostat) turns on and then dims again and the iron doesn't heat up at all. Any pointers on what needs to be done .. Model is TexStyle Control - BraunSI 18895 2400 Watt


... Vacuums

I require to purchase A heat protector capacitor sanyuan ry 240 10A fo A vapoline steam iron from uk


... Vacuums

Breville Digital Colour Select 2200W iron. Flashes red and bleeps. Will not heat up. Any answers gratefully received


... Vacuums

I cant detect where the damage but it dosn't work or even the light indicator didn't open, no heat even in maximum level, i plug in for almost an hour but the iron is not responding or not really working and still cold.... how can we fix to make this appliances work again? tanx,


If it's an old iron, then maybe there is some loose wire inside, which could be fixed with proper tools and some knowledge of electricity, but if you are not familiar with taking apart electric appliances - you should just replace it, because it is p ... Vacuums

Oreck JP8100CB won't heat up


... Vacuums

I have an old 1963 S-11 never used Presto steam/dry iron that has some dark marks on the bottom of iron. I tried using water and baking soda and rubbing on it. That did not work. What else can I do? What is the bottom of the iron made of? Is the iron no longer useable?


... Vacuums

When I put water in my iron, it pours out from the bottom as I iron and get all over my clothes. I love this iron. This is the first problem I have ever had. I have a Rowenta Advancer.


... Rowenta Vacuums

I am a Philips pensioner and purchased a "AZUR EXCEL PLUS 555" steam iron from them many years ago.There is now a fraying of the cable as it leaves the iron with resulting in arcing. There is a detachable backplate on this model which allows corded or cordless use but which cannot be accessed to allow for cable repair by the user. My qustion is can this be repaired or if not can I still purchase a replacement backplate complete with new cable as I this is a great iron and a credit to philips


... Vacuums

My iron is dripping water my model number is dz6080 focus do i need a new one? It is coming out of the bottom when it is sitting upright. my ironing board is all stained and actually my floor is rusted from when I fold up my board and put it away it drips from the ironing board. I paid alot for this model.


... Rowenta Vacuums

Ironed synthetic material whilst iron was set on hot for ironing cotton now the surface of sole plate has a residue of the synthetic material one sole plate is there a way to get rid of this residue


... Vacuums

I have a Euro Pro Compact Performer model # EP 171 which I love. It is the best iron I have found for my quilting class. When I went to use it, I found my cats had chewed the cord to the point that it is unsafe. I took it to a repair shop to have a new cord put on it and they told me it had to go back to the factory. I do not want to purchase another iron because it is my understanding this model is no longer made and because I love it. May I send this iron back to the factory to have a new


Hi, you may already have found a solution, but I recently saw this same model iron on ebay! ... Euro-Pro Vacuums

Model Mars A4 laminator not heating up. The red ligh5t comes on but then wont go green. No heat being generated. Was wondering if it is the round thermistor on inside of the unit, or could it be the heating element itself.


... Vacuums

I have the euro steam blaster s3325 when I turn it on, the steam ready **** comes on right away not heating can the heating element be replaced? thanks


There is a device attach to the heating element called a thermo fuse, this devise brakes down when it get to hot.open the machine and replace it with the same value. it is written on it.. ... Euro-Pro S3325 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0221 seconds