Having problems with your Vacuum ?

Eureka vacuum 5893 bvz has low suction

Low low suction

Answers :

Repair Help & Product Troubleshooting for Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Low suction on Eureka spinduster vacuum cleaner


The belt has stretch enough so as to not drive the brush roll under load. Try a new belt. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

New Eureka 5893 BVZ looses suction


Eureka is about the most helpless website ever!!! did u try cleaning the filters? ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

No Suction I have the Eureka Upright Vacuum. I have no suction when doing regular vacuuming but it seems to have function with just the hose. Also, the height adjustment doesn't seem to work at all. The vacuum has only be usede 3 times. Thanks


Is your brush roller turning? unplug the vacuum and see if you can turn the brushroller by hand.if it turns real freely the the belt is broke ,if its real hard to turn then something is caught up around the bearings on the ends of the roller.my sugge ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

New eureka vacuum has not real suction


Is the belt slipping. Are all the seals good ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative


Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!


If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Eureka 2961 BVZ no suction, burning smell


I have the same vacuum. The burning smell is letting you know that your belt is either broken or about to break. I have had mine for a year and have had to replace the belt 5 times. Now I have to replace the brush roller 'cause it broke under normal ... Eureka 2961AVZ Bagless Upright Vacuum

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"


... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?


That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My eureka vacuum won't suction and starts to smoke when I try to use it. It sounds like it is suctioning when I first turn it on, but after about 20 seconds it begins to smell like burning and does not suction at all. I have tried cleaning and unclogging the filter and everything. It's bagless so I don't need a new bag.


The problem is that your belt is stretched and worn. This causes that burning smell and it also causes the vacuum to not pick up well. You need to replace the belt. Here is the belt you need and the manual with instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Eureka Maxima, this was a gift to me, but I have to say it is the worst vacuum I have ever used. Not only do I have a problem with the suction and the filter getting clogged, but it overheats - it takes me all day to vacuum my house, because the darn thing overheats after every room. Besides for tossing it off a cliff and buying a better vacuum, what can I do?


Get yourself a dyson ... Eureka Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

'eureka whirlwind lite' vacuum - brushes turn but no real suction


... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Hello, I have a Eureka 71b handheld vacuum. There is literally no suction. I checked the hose and it is NOT clogged. I thought it might be the filter so I bought a new filter. Still no filter. The rot


... Eureka Vacuums

Low suction from central vacuum. Unit seems to be


... Hoover Vacuums

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

No suction power on my eureka boss vacuum (vacuum bag has been changed)?


Most probably a clog in the neck. This is where the power head connects to the body of the machine. Remove the base plate (screws in). Take a look at the back of the head behind the beater bar. There is likely something blocked in the nec ... Eureka Boss 7601 Bagged Upright Vacuum

My eureka vacuum model 4341 has no suction. The belt still turns the beater bar and the power still turns on but there is no suction both underneath and when using the attachment.


... Eureka 4341 Vacuum

Low Hose Suction, Hose is open. - Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum


Thanks for the clarification.since the hose in unclogged, the next place to look is in the body of the vacuum.there is usually a tight turn in the dirt channel in the base. often you can see the clog if you remove the hose.the ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Rainbow d3c beaterbar has low suction Vacuum itself has great suction


Did you check the hose or the power nozzle it might have holes in it. ... 3M SV-497AJM Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0776 seconds