Having problems with your VAX Appliances 2000 Canister Vacuum ?

Have a vax power 6 and wont turn on ? - VAX Appliances 2000 Canister Vacuum


Answers :

Repair Help & Product Troubleshooting for VAX Appliances 2000 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a vax power 6 and wont turn on ? - VAX Appliances 2000 Canister Vacuum


... VAX Appliances 2000 Canister Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Hyla wont turn on - VAX Appliances Vacuums


... VAX Appliances Vacuums

Power rewind cable is jammed - VAX Appliances 2000 Canister Vacuum


... VAX Appliances 2000 Canister Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?


... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

The vacuum comes on but the standup vacuum assessory won't turn on. I"ve pushed the reset button; unhooked everything, including reattaching the canister but it still wont' come on. Any other ideas? By the way, I hated the price, but it's the best vacuum I've ever had - especially when I have three shedding pets!


Check the roller brush to see if anything is wrapped around it. If not, there may be a loose connection or wire between the canister and the power nozzle. I assume that's the accessory you're referring to. I could also be a defective switch, but loo ... Vacuums

Rotating brush will not turn om Vax Mach Air - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Change fab belt on vax power pet 1 - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have an Oreck canister vacuum, it says fc1000 on the bottom sticker, it's red. My problem is that the suction in it works perfectly, the belt is ok, and the roller can turn, but the motor doesnt turn it when I turn on the power.


... Vacuums

Vax power 2 remove cover - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

Bottom part of hoover wont **** - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I need a manual for the vax 121 - VAX Appliances 2000 Canister Vacuum


... VAX Appliances 2000 Canister Vacuum

Dyson canister power head won't turn - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Central Vacuum works when power switch on canister is turned on, but will not turn on when connecting the hose.


DOes it not work on any of your wall inlet valves? If all wall inlets appear dead take a coin making a connection with both of the contacts inside the throat of the valve. If the vacuum turns on the problem is in your hose or the powerhead. If nothi ... Kenmore Vacuums

I have an Electrolux Silverado deluxe canister vacuum that won't run. It was running fine, I turned it off to move the plug and then it won't turn back on. It is getting power to the switch. Any help?


... Electrolux Vacuums

My Bissell Lift-Off MultiCyclonic Pet Upright Vacuum with Detachable Canister, Bagless, 89Q9 quit working while I was vacuuming. The power ceased and now it won't turn on. What should I do?


... Bissell 89Q9 Bagless Cyclonic Vacuum

Vax upright brush bar not turning - VAX Appliances VZL-6012 Bagless Upright Vacuum


... VAX Appliances VZL-6012 Bagless Upright Vacuum

How do i change belt on my vax power pet 2 - VAX Appliances Vacuums


... VAX Appliances Vacuums

We bought a new cord winder for our Electrolux 1205 Canister Vacuum cleaner and we are trying to install it is not turning on. We get it all connected but it doesn't turn on. Is there a reset button or some advise you can give me to get it working? I used a voltage detector to see if there was power running through the cord winder and there is.


Did you put a bag in the vacuum?\015\012I suspect there's an improper wire connection somewhere, but there are other things that could cause this I strongly recommend taking it to an authorized Aerus Electrolux dealer and letting a trained tec ... Electrolux Vacuums

What to do if a vax mach2 overheats? - VAX Appliances 2000 Canister Vacuum


... VAX Appliances 2000 Canister Vacuum

My red kenmore canister vacuum cleaner model 721.23083500 stop turning on no power while i was vacuuming just stopped


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1369 seconds