Having problems with your VAX Appliances 2000 Canister Vacuum ?

I have a vax u90 vu p a vacuum which is very noisy,any suggestion to lower the noise? thank you.

Answers :

Repair Help & Product Troubleshooting for VAX Appliances 2000 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a vax u90 vu p a vacuum which is very noisy,any suggestion to lower the noise? thank you.

... VAX Appliances 2000 Canister Vacuum

I have a Vax u90 vu pa,it works very well but very noisy,any suggestion to lower the noise? Thank you.

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thank

What brand vacuum is it? ... Vacuums

Hi folks, my beam vacuum makes a very loud roaring noise quite often. the problem started when i was vacuuming up a quantity of vermiculite from my chimney. i think i overloaded the vacuum i think and it made this loud roaring noise. the vacuum tends to make thos noise when i am hoovering after 5 minutes or so. any ideas?. thanks in advance Tom....

If the filter bag is bad and didn't trap all of the dust, then it got into your motor, so you may have a problem with your motor now. ... Vacuums

How to change cable on vax u90-p4-b - VAX Appliances Vax X3 Bagless Upright Vacuum

... VAX Appliances Vax X3 Bagless Upright Vacuum

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you

Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!

Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

My vax vacuum has started making a high-pitched whining/whisting noise

Ususally this is caused by a forein object has gotten hung in the suction impeller attached to the motor. the noise flucuates due to the housing flexes with the movement of the handle and rod. the housings are usually made of plastic and something ve ... Vacuums

Hissing noise on my Vax mach air - VAX Appliances Vacuums

... VAX Appliances Vacuums

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!

These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

Loud noise My Westinghouse Wired vacuum works fine, but is making a very loud noise. any suggestions?

When the motor bearings start to go bad, they will make a loud noise. Some motors if a piece broke off of the fan, then it also will make a loud noise. You may have to replace the motor. ... Westinghouse WST1500 Wired Special Edition Upright Vacuum

I replaced the belt on my model 3920 because the vacuum was very noisy. It is still making the noise. It is so loud that I am concerned that there is some other problem with the vacuum. Any suggestions?

Sounds like an obstruction in the blower motor fan or bad bearings in the blower motor located in the bottom end of the main body ... Bissell 3920 Bagless Upright Vacuum

Hi my vacuum (Russell Hobss 2200 bagless HEPA) seems to have just enough ( not loads) of suction til it reaches the cleaning head. the head does not appear to be blocked - but there is then almost no suction at all. It also makes loads of noise when on- and an even louder noise when turning off. is it fixable or is it dead? Thanks

Generic problem for all Vacuums\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA)\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA) seems to have just enough (not loads) of suction til ... Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank

You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

I am losing suction and it sounds as if there is a leak in the vacuum(I hear air rushing around). There is also a high pitched noise. Dyson dc07. Can there be leaks in the gaskets where you clean hoses and filter? are they replaceable. Does the noise suggest the bearings are going in the motor?Is it worth getting fixed?

It wont be a gasket problem - they don't tend to fail. \015\012\015\012A high-pitched noise can be a number of different things. That is too vague to diagnose on here with the description you have given. Can you be more specific? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the

Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum

I accidentally sucked up a strap from a bag, and when I pulled it out from the vacuum the vacuum now makes a loud noise only when the brush is rotating. Please help! Thank you!

Is it the vacuum making a loud noise, or the power head. I'd say the belt in the power held came apart and is flapping around inside. You may be able to replace, but I recommend taking it to the dealer for repairs. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Loud noise I have a Shark UV610 model of the Cordless sweeper. All of the sudden there is now a loud noise when I turn on the power to vacuum. Any suggestions?

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

I have a VAX U91-MA-B-I vacuum. All filters are clean. When I start it a valve in the upper part of the canister (near the handle) opens and the vacuum makes a very loud noise and does not create the cyclone in the chamber.

... VAX Appliances Vacuums

Loud Noise When I start the vacuum, there is a loud noise that sounds kind of like a table saw. It may be because I placed the bag on wrong and the dust may have clogged something. Do you have any suggestions?

Loud noise that doesn't stop. changed bag, cleaned roller, etc. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Dyson D23 Vacuum just stopped and it won't turn on no noise nothing stopped completely now what any suggestions?

... Dyson DC23 Bagless Canister Cyclonic Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hi I have used my Vax 123 agility for the first time today and found the solution is not going into the recovery tank just seems to be staying in the carpet! Any suggestions thanks

... VAX Appliances Vacuums

I replaced the clutch in the dyson dc14. it isnt making that terrible noise anymore....thank god!! but the roller brush is not moving when the vacuum is in use. whats wrong?

The "horrible noise" you were hearing before wasn't the clutch! It was the roller brush. If the brush is not turning, all you are doing is burning out your new clutch. Reasons for the brush not turning: there is hair, carpet fiber or other matter wra ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1235 seconds