Having problems with your VAX Appliances Vacuums ?
Vax power 8. all muck goes direct to filter, seems to bypass bucket.
\015 I have cleaned filter so many times its got silly now, all the muck gets sucked up ok, but seems to come out into top of bucket and gets sucked down to the filter and not into the bucket. any ideas please. the seal at the bottom of the bucket at the "trumpet" does not seem all that great but still cannot understand why stuff comes into bucket then sucked down to filter through the "trumpet",\015
Repair Help & Product Troubleshooting for VAX Appliances Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vax power 8. all muck goes direct to filter, seems to bypass bucket.
... VAX Appliances Vacuums
Dyson absolute dirt bypasses tank and goes to filter
Check rubber seals ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho
... Electrolux Vacuums
Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.
Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you
Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums
Vax power pet 9 which way up does pre motor filter go ?
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
My electrolux oxygen cannister has the "bag change" light on when there is a new bag. The light stays on when the suction power is high (to pick up small particles) and it won't pick up, but the ight goes off when the suction power is low (to pick up big objects). I changed the hepa filter, cleaned the motor filter and changed bags, but all that didn't help.
You may have a clog in the hose, and/or the inlet by the brush roll. A clog will turn on that light as well as a full bag. ... Vacuums
We have a zenith dehumidifier model ZD300 & the bucket full light keeps flashing. the percentage number wont go higher than 1%. we have turned it off/on & unplugged it. When we do this it will reset to 40% for about 2 seconds & then goes back to 1% & the bucket full light starts flashing again. The bucket is empty & we have cleaned the filter. We have only had this dehumidifier about 7 months. Please help us.
I've had the same issue with mine. I am a 12 year refrigeration tech. I checked the float switch which would normally cause that indication light. However manually pushing the switch and then checking it with an electric meter that was not the case. ... Vacuums
Hi: I have a 14 month old EL7024 Oxygen that has no power. Will not turn on. No power at lights that are usually flashing. Wall receptical has power. Does not seem to be a thermal reset, full bag or plugged filter. Owners manual is no help. DAve
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
VAX POWER 6 PET...BACK FILTER CONSTANTLY BLOWING OFF....HOW CLEANED FILTERS NO CHANGE
Smart hoover when hoovering the dirt dosent go into bucket but goes where filter is help
... Hoover Clean Smart Cyclonic Upright Vacuum
Vax CCW-201Rapide Spruce Upright: Seems to have no power
Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen
Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum
My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga
I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums
My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u
Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums
The mechanism that rolls back in the power cord seems to be working slower and sometimes not at all. Was wondering if the mechanism in question has an adjustment to increase the tension on it so the power cord goes in faster like it used to. Thanks Rafael
It easy to adjust the roll back of vacuums the problem is hard to dismantle the unit to remove all the things to see the adjustment roll,all vacuums is need to remove all screw to open the unit even to replace the small parts like switch,and sometime ... Kenmore Vacuums
I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.
... Dyson DC25 All Floors Bagless Upright Vacuum
I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?
There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum
I have the Bissell power force bagless upright vacume and I took the filters off and cleaned them and don't know where the round filter goes to be able to continue vacuming.
I had shortly after posting the question requesting help and then found the product manual.\015\012\015\012Thank you very much though. ... Bissell Vacuums
My Roomba Discovery 4210 seems to be dead. Specifically, with or without a battery, and whether on the charging station or plugged directly into the charging unit, I see no lights on the display whatsoever. This unit has a history of killing batteries, but now seems like it is completely dead. I understand that the batteries themselves contain fuses; is there some way to bypass the battery (for now) to verify whether the unit itself is completely dead? I should also note that this is the sec
Hello,I will advice you remove the batteries from your Roomba Discovery 4210, after removing the batteries, plug the Roomba Discovery 4210 directly with the charger to an AC outlet, see if charges, if it does, it means the batteries are d ... Vacuums
Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.
Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum
CANISTER IS GETTING POWER BUT NO SUCTION FROM HOSE AND DOESNT SEEM LIKE THERE IS POWER GOING TO HOSE..I HAVE CLEANED OUT THE FILTER AND CHECKED ALL BREAKERS...
Hello,Carnister vacuum cleaners are all built with the same \015\012principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are ... Hoover S5615 Hush Central System Vacuum
I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!
... Miele S7210 Bagged Upright Vacuum