Having problems with your VAX Appliances VZL-6017 Bagless Upright Vacuum ?

Vax mach 7 brushbar

\015 Brushbar not turning, belt changed but still slips\015

Answers :

It is either the brush that is worn where the belt fits or it is the drive pulley (the other end of the belt). Check both closely for signs of wear but probably a worn drive pulley is favorite. They cost about 12 quid and are held on with four screws.
Repair Help & Product Troubleshooting for VAX Appliances VZL-6017 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vax mach 7 brushbar


It is either the brush that is worn where the belt fits or it is the drive pulley (the other end of the belt). Check both closely for signs of wear but probably a worn drive pulley is favorite. They cost about 12 quid and are held on with four scre ... VAX Appliances VZL-6017 Bagless Upright Vacuum

How to change a brushbar on a vax mach air reach


... Vacuums

Vax mach 3 allergy new belt how to fit - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Rotating brush will not turn om Vax Mach Air - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Hissing noise on my Vax mach air - VAX Appliances Vacuums


... VAX Appliances Vacuums

Vax mach air reach vacuum cleaner user manual


... Vacuums

Vax mach 7 upright overheating and no suction


... Vacuums

How to replace belt on vax mach air


... Vacuums

I have a vax mach air u91-ma-b where's the drive


Click on the link below and you can dowload the manual witch will give you instructions how to change the belthttp://support.vax.co.uk/power-2-upright ... Vacuums

Vax mach 5 burning smell and revving loud


My mach 5 has lost suction and the brushed are spinning ... Vacuums

Need to down load instruction manual for Vax U89-MA-PF mach air bagless upright cleaner


... VAX Appliances Vacuums

Vax air 3 brushbar blocked


... VAX Appliances Vacuums

Vax Mach 7 - the brush bar won't rotate but the belts are fine


... Vacuums

I have a vax mach air - Vacuums


Please the scheme for fix it.God bless you ... Vacuums

I have a vax mach 6. There is very little suction when using the tools and it will switch itself after a few minutes. I have had it to bits and cleaned it. I can not find any blockages. The belts also seem fine.


Http://www.vax.co.uk/downloads/pdf/u90-m5_u90-m6_series_user_guide.pdf ... VAX Appliances Vacuums

Roller brush not working on vax air mach 6


Hi I have a vax mach air light.the brushes wont turn but the green light is on. I have checked eveything .The little button on side tube no blocks .Checked all filters. ... VAX Appliances Vax X3 Bagless Upright Vacuum

Vax mach 7 cable rewind spring has detached - Vacuums


... Vacuums

Vax mach xp reach seems clogged and light is on


Clean the filters as per the user guide AND remove the silver, where the clear plastic handle is. On te back by the purple catch to release the dirt container is a screw - remove that and then remove the 3 screws on the purple lid with holes in it, r ... Vacuums

Red light on vax mach air - Vacuums


... Vacuums

Instruxtionsfor puttin a belt on a vax mach 2 model u91-m2 -b


... Vacuums

Vax Mach 3 Cylinder Hoover


... VAX Appliances Vacuums

How to fix vax mach zen


... Vacuums

Vax mach 7 cuts out then restarts after a few minutes


... VAX Appliances Vacuums

Brushes not working on vax mach air


... VAX Appliances Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0127 seconds