Having problems with your Wap Vacuums ?

SQ10 rdf Wap industrial vac. Removed two screws holding cover on. Cover won't come off.


Answers :

Repair Help & Product Troubleshooting for Wap Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SQ10 rdf Wap industrial vac. Removed two screws holding cover on. Cover won't come off.


... Wap Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Upright model # el8605 cannot remove screws that hold on brush @ belt cover have tried to loosing them but they just turn and will not come off


... Electrolux Vacuums

We have a Eureka 71B Hand-Held Vacuum and it looks like the belt broke. I removed the two screws at the bottom that should release the housing that holds the belt. However, the housing still does not come apart. Any advice? Thanks.


There's a 3rd screw hiding underneath a plastic shield. You'll have to drill or cut off the covering but then it's pretty easy to deal with. ... Vacuums

Upright model # el8605 cannot remove screws that hold on brush @ belt cover have tried to loosing them but they just turn and will not come off


... Electrolux Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian


... Panasonic Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.


... Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor


... Eureka 3041BZ Upright Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

Vacum I need to check the brushes in the motor smells have removed four screws but the cover is not coming off. I dont want to damage this by forcing it but cannot find any other screws Thanks fairweather


Hi there!\015\012\015\012It would certainly help if you said which model it was.\015\012\015\012I can only give generic help now, and do the best I can for you.\015\012\015\012Most plastic products rely heavily on ... Vacuums

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do i disassemble (i.e. which screws do i pull and which hidden tabs are there) the cord retractor/switch assembly? there is only one screw that appears to hold the piece but it does not come out, Thanks


There are 7 torx head screws to remove in the top plastic housing. 5 are in the perimeter and two are "hidden". One is under the power/cord winder panel which pops off in an upward diredtion. and one is under the cloth filter on top of the motor, ins ... Miele S514 Solaris Bagged Canister Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet


Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?


... Panasonic MC-3900 Bagged Canister Vacuum

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?


Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.


That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0490 seconds