Having problems with your Westinghouse Vacuums ?

Westinghouse 77875 is there wires to attach ceiling fan to ceiling? do you need an existing power source?

Answers :

Repair Help & Product Troubleshooting for Westinghouse Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Westinghouse 77875 is there wires to attach ceiling fan to ceiling? do you need an existing power source?

... Westinghouse Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?

They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available

Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,

... Bissell Vacuums

Need to replace power cord on Hoover windtunnel need wiring help

Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Rowenta Effective Steam Iron DX1700 Need wiring diagram. How do I wire the power cord to the internal Red, Blue, and White wires? What wires are neutral and which are hot?

... Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals

... Vacuums

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?

I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

Heritage 2 - black wire pulled out from motor assembly, comes from power switch. Where does it go? Need wiring pictorial and schematic/wiring diagram. Can anyone please help? Many thanks, Malcolm

... Kirby Heritage II Vacuum

I restored my Eskimo fan and its not turning on? I think I just have one of the wires wrong. I just need the schematics to it to check that I wired it right.

... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

I have a Fantom, Cyclone XT vaccum and while attempting to clear a blockage the wires inadvertantly came loose from the power on/off selector switch located on the top front of the unit and I need to reinstall the wiring in the proper order

... Fantom Vacums Cyclone XT Upright Vacuum

Rainbow mod. D4C have new on /off switch, 2 black, 2 blue wires. need to connect power cord, motor and carpet sweeper?

Are the wires still attached to the old switch? If they are, hook them up to the new switch in the same, physical way. If they aren't attached, you might take it into a vacuum repair shop- they could probably help you figure it out, if you bought ... Rainbow Technologies D4 Bagless Vacuum

The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.

It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums

I need a wiring diagram for the power head, model S3601.

Hi,\015\012\015\012It would be better f you can find the Model Number as some of the manuals are applicable for different models of Hoover vacuums and for this reason the manual may not have the exact name of your cleaner on it.\015\012\0 ... Hoover Powermax S3601 Bagged Canister Vacuum

Need a wiring diagram for the lakewood kool operator floor fan

... Vacuums

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

I have made electrical connention wrong -only power switch works but not the brush. I need electrical wire layout diagram for Bissel 3760-2

Send me your unit.. ... Bissell 37603 Upright Vacuum

Rplacement part I need the part # or a schematic so I can determine the part # for the little black cylinder with 4 wires sticking out of it that commects the power cord to the two motors.

Http://www.oreck.com/customer-service/owners-guides.cfm#Her is the oreck manuals web page.They can also tell you where to get parts. ... Oreck XLS700A Upright Vacuum

HOW DO I CHANGE THE MAINS POWER CABLE ON A DYSON DC07? my wife cought the cable under the dyson and has stripped it to bare wires so i need to change the cable. i have taken a cover off near where the cable goes into the machine but now cannot get any further

How to open the cover near the cable for dyson upright vacuum ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a pms4 power management system and i need a installation or wiring diagram for it can you help

... Vacuums

I need wiring diagram to connect power cord, motor, and switch on a shop vac

... Shop Vac 84M200 Wet/Dry Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1302 seconds