Having problems with your Westinghouse WST1550 Wired Deluxe Upright Vacuum ?

How do I open the vacuum assembly?

\015 I can't find a way to access the motor housing area. Can someone explain where the access points are or what screws will release the cover?thanks.\015

Answers :

You have to take the headlight lenses off with a small screwdriver. then a philips screwdriver to take the 2 screws out. one each side. then remove the foil shields on each headlight . then snap loose the rear plastic clips on the cover and it will come right off. it took me an hour to find out how and 10 minutes or less to take it off. watch for the micro switch on the circuit board being worn out.it will stop the roller brush from turning.its a dollar part at any good electronics store ,but will have to be soldiered in or service might have a few from the westinghouse line .so will a broken belt which is a special grooved belt available from fantom at 18007987395..
Repair Help & Product Troubleshooting for Westinghouse WST1550 Wired Deluxe Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.

... Kenmore Vacuums

How do I open the vacuum assembly?

You have to take the headlight lenses off with a small screwdriver. then a philips screwdriver to take the 2 screws out. one each side. then remove the foil shields on each headlight . then snap loose the rear plastic clips on the cover and it will ... Westinghouse WST1550 Wired Deluxe Upright Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

How do I open the hose handle assembly of a kenmore whispertone 4.5 canister vacuum? It seems to start at the sleeve where the flex hose meets the handle, but I'm afraid of breaking it by forcing it.

... Kenmore 23313 Whispertone Bagged Canister Vacuum

When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip

Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum

Hi, I have a Miele s247i vacuume cleaner- My electric coard does not roll back, How do I open the vacuume lid / housing to fix or replace the spring? do you have instruction manual on how to open the cover?

... Vacuums

My Ergospace Vacuum took some apple juice in and now it makes strange noice and even threw out some sparks. Is there anything I can do my self or is it over with this vacuum cleaner? I opened 6 screws, but I still can't open the motor cover. Are there some hidden screws?

Liquid plus electrical parts always ends up with the electrical parts losing. Juices, although they will dry, will leave behind a sticky residue. You'll need to replace at least the motor, but due to the other electrical components, probably be bet ... Electrolux EL4100A Ergospace Cannister Vacuum

On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.

... M&S Systems ZX7000 Bagged Central System Vacuum

Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave

... Vacuums

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?

Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Dyson Animal upright (purple). I took it apart to clean the cyclone chambers. When re-assembling the bottom closed before the opening rod was inserted. I can't get the opening rod installed with the bottom opening closed. How do I open it? Thanks.

I looked in our DC07. I would try removing the top again and getting a long dowel or the opening rod, insert it down into the unit and PUSH. The opening rod opens the latch by pushing it, not pulling it. Here are some pictures of the latch. Top pi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to open a electrolux 4602 vacuum cleaner - Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.

Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

How do you open the vacuum - Dirt Devil KURV Hand Vacuum Champagne Vacuum

Wish I knew! We've tried everything and can't get it open. ... Dirt Devil KURV Hand Vacuum Champagne Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

I removed the brush from bottom of the vacuum to remove hair from the bristles. When I re-assembled the vacuum, there was no longer suction. Also, the vacuum no longer stands upright when not in use. It's like something is blocking the upright portion from locking.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.

You need to replace the belt. Replacement Vacuum Belts ... Vacuums

I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you

Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums

I do not know how to open the vacuum to get access to change bags. the bosch pro parquent vacuum cleaner

... Bosch BSA2822 Pro-Parquet Bagged Canister Vacuum

Lid to kenmore canister 360 hepa vacuum cleaner, lid to change vacuum bag stuck in open position

GoVaacuum2,\012\012I have the same problem and that didn't work.. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hoover Telios TC3202 200W Cord Rewind is jammed - cannot see how to open body of vacuum to look at the source of the problem. Found 4 screws but that did not help - guess you have to prise something open but cannot see where or how.

There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about the others. \015\012Anyway, this is it. The cover is held to the b ... Vacuums

I have a Kenmore Destiny Plus vacuum, and it doesn't have suction anymore. I've come to the conclusion that the tubes, I guess you can call them that, are plugged. I'm trying to find the user manual/service manual to know how to open the vacuum up to unplug the tubing.

It's October now so this is probably too late to be useful for you but it might help someone: I had the same problem. I used a bright light to see that there was a clog up high in one of the plastic tubes on the side. Using an untwisted wire coat han ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0604 seconds