Having problems with your Windsor SR12 Sensor Bagged Upright Vacuum ?

How to replace the belt on a windsor s15 vacuum

\015 Vacuum has no suction and not picking up\015

Answers :

Repair Help & Product Troubleshooting for Windsor SR12 Sensor Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace the belt on a windsor s15 vacuum

... Windsor SR12 Sensor Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Need to replace belt on Windsor Sensor 12 vacuum

... Windsor SR12 Sensor Bagged Upright Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.

... Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.

... Panasonic MC-V7515 Bagged Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.

... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?

Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t

It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

Replace belt on fantom cyclone vacuum? the manual does not decribe replacing the roller belt - i can't get it open to expose the belt

On my 10-year-old model, the two screws securing the cover are under the two llight bulbs. Pry off the clear plastic covers, take out the bulbs and screws, and the cover lifts off. ... Fantom Vacums Cyclone XT Upright Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.

Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks

You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

I have the same rproblem with my little Shark V15Z hand held vacuum. the belt broke,there's no instruction on how to replace (and apparenlty it was not designed to be replaced (at least with out a lot of research). I see BElectric describes how to find the hidden path, but now where can we buy the correct belts??

... Euro-Pro HEPA Shark EP035 Bagless Handheld Vacuum

I need a replacement belt for a V1315 Shark Roadster Vacuum cleaner. Looks like there's no way to get one. Is there a compatible belt that will fit this vacuum?

... Euro-Pro Roadster V1315 Upright Vacuum

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]

A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

My belt broke and I cannot find a replacement anywhere. Can you tell me where I can buy replacement Sweep n Groom belts for my central vacuum system.

You can get replacement Sweep n Groom belts here:\015\012\015\012Sweep n Groom Belts ... Vacuums

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01

... Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0771 seconds