Having problems with your Windsor SR12 Sensor Bagged Upright Vacuum ?

Change wheels on Sensor SR12

\015 I have new wheels and cannot figure out how to change the rear wheels on the Windsor Sensor SR 12.\015

Answers :

Repair Help & Product Troubleshooting for Windsor SR12 Sensor Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change wheels on Sensor SR12

... Windsor SR12 Sensor Bagged Upright Vacuum

Roomba 550 will not go forward, only turns and moves a few inches in reverse. I changed out the wheel motors with no results. Cleaned bumper and sensors with no results.

... iRobot Roomba 550 Vacuum

Front wheel problem

I would send it to protechrobotics. they will test all your components and let you know what needs to be done. if the repair is more than it's worth--they will help you out too.http://www.protechrobotics.com/ ... iRobot Roomba 4210 Bagless Robotic Vacuum

Roomba pro elite change drive wheels

Just click the below link...ur pro will be solvehttp://www.wikihow.com/Fix-a-Vacuum-Cleanerthanks for using fixya...rate tis solut ... Roomba Pro Elite Bagless Robotic Vacuum

My windsor sensor xp12 wont turn on - Windsor SR12 Sensor Bagged Upright Vacuum

... Windsor SR12 Sensor Bagged Upright Vacuum

Windsor Sensor XP18 brush - Windsor SR12 Sensor Bagged Upright Vacuum

... Windsor SR12 Sensor Bagged Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.

It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

How do you change the belt on a winsor sensor s12?

Step 1. Remove the vacuum bag housing so that you are only working with the power nozzle or the bottom portion of your Sebo, this will make it much easier to work with. Turn the vacuum upside down, and remove only the 5 screws that I have circled in ... Windsor SR12 Sensor Bagged Upright Vacuum


It is 0.027 inch thick and 0.28 inch inside diameter.Or just go HERE and buy it. However we ship only PRIORITY and we have 2 ... Kirby G5 Bagged Upright Vacuum

How do you change the fly wheel?

If you meant the FAN. then HERE is the instruction ... Kirby G5 Bagged Upright Vacuum

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.

... iRobot Roomba 550 Vacuum

My kenmore vacuum 35922502 sensor dirt lights stay on red all the time. I have changed the bag, filter, little sponge filter, still they stay on. What is wrong? Lynn [email protected]

... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Changed wheel and roomba starts but shuts off in 2-3 seconds

Make sure all wires are connected properly, make sure all parts move freely with ease and nothing is binded up. Make sure any service doors are completely shut.If problem still remains, then either there is a faulty control circuit, or a part ... Roomba Pro Elite Bagless Robotic Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga

Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!

Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

Windsor sensor sr12

There is a downloadable manual from http://www.windsorind.com/ go to documents, and note it is in alphabetical order -- so page through to "sensor" or you can search on the wo ... Windsor SR12 Sensor Bagged Upright Vacuum

My roomba pro elite just goes around in a circle. how can I fix this? I have cleaned the roomba as thoroughly as I can. Could it be a recently changed wheel tread?

The infrared sensor circuit has failed, u will need to have it repaired ... Roomba Pro Elite Bagless Robotic Vacuum

WIndtunnel TurboPower U5400-900 sensor light flashing even though I just changed bag

They do this as a matter of course. its a poorly designed vacuum. Hoover doesnt exist any more, it is actually a dirt devil\015\012after years in the vac repair business, i reccommend that you look at panasonic the next time ... Hoover U5420-900 Bagged Upright Vacuum

Need to replace vacuum door - Windsor SR12 Sensor Bagged Upright Vacuum

I pried up the back of the cover holding the height adjustment wheel and was able to snap the cover axle with the cover installed into place. ... Windsor SR12 Sensor Bagged Upright Vacuum

The Intelliclean function isn't working properly. The indicators illuminate when I switch Intelliclean off, then on again, but the indicators are not changing (nor the power level) when I vacuum dirty areas. I need to install new filters, could a dirty sensor be the problem?

I was having the same problem with my Intelliclean and I read somewhere on the internet that I should undo the bag, clean in the area where the bag attached to vacuum. When I took bag off, something was stuck there and after I removed it, everything ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Can you help me change the Sensor in my Sebo Auto X-1

Do you still need help with this, or has the moment passed? If you still want help, please state why you think the sensor needs changing. ... Sebo Automatic X1 Bagged Upright Vacuum

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

The roomba 560 keeps going in circles after it hits an object. Or it will keep hitting the object repeatly until you pick it up and move it. I have cleaned the sensors and wheels and it still does not work properly. Thank you.

... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0311 seconds