Having problems with your Windsor VS14 Versamatic Bagged Upright Vacuum ?

Broken motor pulley windsor vacuum

\015 How do i remove and replace motor pulley gear on a windsor vacuum\015

Answers :

I have the same problem, maybe we can flip the belt over and let it run on the smooth side for a while. That's what the person before me did and it lasted a good 6 months.
Repair Help & Product Troubleshooting for Windsor VS14 Versamatic Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Broken motor pulley windsor vacuum

I have the same problem, maybe we can flip the belt over and let it run on the smooth side for a while. That's what the person before me did and it lasted a good 6 months. ... Windsor VS14 Versamatic Bagged Upright Vacuum

Broken Bag + Dirty Motor = Squealing Vacuum

... Electrolux Guardian Bagged Canister Vacuum

Will the broken pre-motor filter housing catch affect the overall suction of the vacuum?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My hoover 600 elite is really load. I took it all apart to find the motor fan is damaged with a broken off piece which must have been vacuumed up into the bag. If I replace it sith a new plastic fan will this quiet the vacuum? right now it is tremendously loud.

... Hoover Elite U5061-900 Bagged Upright Vacuum

Belt motor pulley on a bissell powerforce bagless vacuum

Yes, the motor shaft is also the pulley. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.

... Eureka Sanitaire S661 Bagged Upright Vacuum

How do I change the belt on my Hoover Elite Dual Purpose Vacuum cleaner? The belt part # is 38528-027. Where is the motor pulley?

The hoover belt number you listed (38528027) has been changed by Hoover to 38528040. Below I have listed a link to the manual that has instructions and a link to the belt you need. Hope this helps! ... Hoover Elite U5061-900 Bagged Upright Vacuum

The clip or latch that holds the Motor Inlet Cover of my Dyson DC14 is broken. Any way to fix this? It appears attached to the large body of the vacuum.

Hi there,I'm sorry to hear the catch has broken on your DC14. Our Helpline should be able to assist you in resolving this - please give us a call free on 0800 298 0298 (UK), or 1-866-693-9766 (US). It will help if you have the machine to hand ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums

Shark Navigator Vacuum Motorized floor brush nozzle wires broken and completely disconnected from swival

... Shark Vacuums

Rotating Floor Brush will not rotate. The Drive Belt is not broken and the Motor Pulley appears to be rotating.

I did not receive a solution to this problem. I will be purchasing a new vacuum (probably not a Bissell) to resolve this situation. Thank you. ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

I have a Euro-Pro Shark UV-204. The Vacuum turns on, motor sounds fine, and suction is as strong as ever. Still picks everything up in its path. However, the bristels on the bottom do not rotate around, the belt is not broken or loose. Is there something I'm missing?

... Euro-Pro Shark UV204SH Bagged Upright Vacuum

Broken belt, motor wont turn - Vacuums

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=721048\015\012Generic problem for all Vacuums\015\012Broken belt, motor won’t turn\015\012Posted ... Vacuums

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean

... Panasonic Vacuums

Eureka 9410 upright vacuum motor

... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.

If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the

Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.

... Miele S251 Flamenco II Bagged Canister Vacuum

Nutone model cv-350 vacuum motor will not shut off. I have to unplug system in garage. I disconnected wire to house vacuum inlets and motor is still running. There must be a reset on the motor. I have turned the external switch on and off and still no help.

Mine is the same, and it is the relay welding itself closed. The relay is switched by the low-voltage wiring that connects to the vacuum outlets, and it switches the motor on and off. Mine was welded in the energized position. I have cleaned and file ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1118 seconds