Having problems with your Vacuums ?
How to replace a belt and brush in a Dyson DC04
Hi here is a video on how to do this.........
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to replace a belt and brush in a Dyson DC04
Hi here is a video on how to do this.........\015\012\015\012http://www.videojug.com/film/how-to-replace-the-belt-on-a-dyson-dc ... Vacuums
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?
Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.
Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it
If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!
Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums
I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.
The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson DC14 Bar brush and belt replacement.
Try the op manual \015\012http://www.dyson.com/customercare/manuals/us/dc14_opmanual_usa.pdf ... Dyson DC14i Bagless Upright Cyclonic Vacuum
Replace belt on dyson dc04 zorbster
I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?
Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dc04 belt replacement - Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
This video will show you ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please
How do I replace the belts on a Dyson DC04 purple
That model has a clutch unit from which the two drive belts are located. It is a technical job to strip that unit down to change the belts, so the easier solution if you have a snapped belt, is to replace the clutch unit (that comes with belts ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes
You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson dc04 drive belt keeps snapping have put 2 new ones on a made sure it was on shaft fully and brush did move before tunring on
... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?
Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
How do i replace a brush bar in a dyson DC04 cleaner
Dyson dc14 How do we replace the belt one I removed it to clean hair from brushes? Can't get it back in place. Any tricks or suggestions. Craig Dittmar
Hi am i right to assume the belt is still in place ie in position around the drive wheel of motor? and you have removed the roller/brush only? and you now have difficulty re assembling the belt on brush and relocating brush into its holder ?? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Dyson dc04 brush unit will not rotate belt ok air circulation in drum. help if you can please.
Clean all filter ... Vacuums
How to replace dyson dc07 brush belt - Vacuums
Hi - You can download the manual by clicking the link underlined in blue below:dyson dc07 ... Vacuums
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom
... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum