Having problems with your Vacuums ?
I have necchi ALICE model purchased in about 1972. Amazing machine but the floor pedal needs replacing and cannot find one.
Code on plate of pedal is A 50305/4 made in italy.I live in montreal,canada.
thanks, ania barnes
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have necchi ALICE model purchased in about 1972. Amazing machine but the floor pedal needs replacing and cannot find one. Code on plate of pedal is A 50305/4 made in italy.I live in montreal,canada. thanks, ania barnes
Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st
Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums
Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J
There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums
Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!
On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
Lost manual for emeril by t-fal bread machine model series bo1 or b01 can't really tell which number 0 or letter o.where can i find one most other products have an on line manual..i can t find one can u help me locate one..thanks
Hi - welcome to FixYa,\015\012\015\012Not easy to track these down and I can't find information relating to B01 or BO1, but I'm pretty sure this is the manual you're looking for:\015\012\015\012 ... Vacuums
How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>
What model is this for? ... Kenmore Vacuums
I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]
Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum
I work in the Pittsburgh Public Theatre costume shop. We have an old Rimoldi industrial serger withiut an instruction manual and can't seem to find one online. It says rimoldi on top and the numbers on the front plate are B.29.17 There are numbers on the back, one plate says 194076 and the other 0901-0962 Thank you- any help would be appreciated, Mindy Gregory
I have a Fuller FB80 and am unable to remove the bottom plate for cleaning. I can only find 2 screws holding it on, but I'm afraid to force it in case I might break the plastic.
... Fuller Brush FB80 Bagless Upright Vacuum
I have an antique White sewing machine. The plaque reads Dressmaster made in U.S.A. It is green cast iron. The numbers on it are 605-9761 and E6354. I cannot figure out how to get the bobbin thread to pull up. Where can I find a manual?
I live in Ogunquit, Maine and attempting to find foot pedals for the Sebo X4 vacuums. I believe the part number is 5059DG. Thanks
Try this website.\015\012\015\012http://vacuumcleanerdealers.com/maine.html ... Sebo X4 Bagged Upright Vacuum
Water not getting to cleaner head when pushing down the pedal. Cant find any blockage, motor sounds ok
Some times the tip /nasal git plugged from soap, it gets crystallized. can try running clean hot water in place of soap. Hope this helps please feel free to let us know if you would like more info. Thank you , Have a good day ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
I think there used to be a metal hanger-like piece of **** holding down the bag at the spot where it is affixed to the vacuum cleaner. I want to find it, and if possible, download the **** manual. Too much to hope for? Hoover Legacy 830.....Model # U5079-910......Serial # 069100005664. Please don't tell me it's SO old they deny ever having made the thing!
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559223\015\012\015\012Generic problem for all Vacuums\015\012\015\012I think there used to\015\012\015\012Posted by imaninvi ... Vacuums
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My McCulloch whipper snipper was working just fine after finding cracked fuel lines,. Replaced wiht home made lines and worked fine until Sunday and now wont start at all . Checked everything , now think its electrical Would like to kow if there is anyone in Perth who can sort this out
Your local lawn mower repair shop will be able to fix it for you. ... Vacuums
There was a foam piece above the motor of my rainbow d4c power nozzle. When I took the plate off it desintigrated and fell off. Was that supposed to be there? If so how do I find a replacement?
You said "above the motor", so I assume you meant the smaller foam piece located there, and not the gasket seal that is affixed to the inside of the metal bottom plate, (which is what the previous solution responder was referring to).Most ... Rainbow 75th Anniversary Canister Vacuum
Replacement parts where can i find replacement steam pocket towels online for the shark ultra steam blaster hard surface cleaner? I went online to www.sharkcompany.com & www.sharkvac.com and when I enter my model number S3325 search comes back with 0. Thanks
You can found them on amazon, take a look here: Amazon com Euro Pro S3325. I hope this was helpful. Cheers ... Euro-Pro S3325 Handheld Steam Vacuum
Kenmoore Intellivac w direct drive suddenly started making internal sound like something was stuck. Hose is clear, and sound is made when hose is detached from main unit. Vacuum sounds find at lower pressure, only makes sound with bag door closed and/or placing my hand over the end of hose.
Shut off the vac and open container and remove the bag. Try dropping a coin into the hose, then raise up to see if it falls thru to the bag area. If it does check the throat of the vac where the dirt is sucked upward to dump into the bag itself. ... Kenmore 35912 / 35913 Progressive Upright Vacuum
My Dyson is very difficult to push forward. I've made sure the brush is spinning freely. How do I find out what is causing this and fix it? thank you.
... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Replacement motor I am undertaking the repair of an old dustbuster as a training exercise. ,The motor in my V2410 is Made by Johnson Electric but I cannot find reference to the numbers marked on it on the manufacturers website. Are you able to give me a model number for an equivalent replacement or the specifications of the original motor? Thanks, Gary.
... Black & Decker V2410 DustBuster Handheld Vacuum
Vibrating When I turn on the vacuum , the bottom where the brush is vibrates to make a loud sound. I cleaned the brush and took the gray plate off. when replaced made louder.
I misunderstood the original suggestion to fix this issue. It was a misalignment on the beater bar. I fixed that and voila! Vacuum is perfect again. Thank you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
Can't find a user manual for a commital sami TR5 steam cleaner. Made in Italy. Cannot put product in the product window
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Where can I find a part for my BV2000 in house vac? It is the smallest unit made by M S & S Systems in Dallas TX. The suction impeller is grinding in it's housing, so I need a motor/suction pump. I have removed this combination from inside the vac assembly
You will have to replace the whole motor as these motors where never made to be serviceable. if you take the motor to a local vacuum shop than can order you a new one. though i would recomend replacing the whole tank unit with a Nutone or Hayden they ... M&S Systems BV-2000 Bagged Canister Vacuum
My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?
Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum