Having problems with your Vacuums ?
Kenmore Vacuum Model 116.35922500
Agitator starts/stops as you change handle position and/or move the vacuum. Seems like a switch, but the diagram shown in another solution doesn't seem to show a switch.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmore Vacuum Model 116.35922500 Agitator starts/stops as you change handle position and/or move the vacuum. Seems like a switch, but the diagram shown in another solution doesn't seem to show a switch.
I changed the belt on a Eureka WhirlWind superlite, all was well but I can't seem to find where this white piece of plastic approx.2" and less than 1/2" wide and there is a copper like V shaped clip, I was hoping maybe you's had a diagram or something showing where these go. Much Appreciated
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552328\015\012Generic problem for all Vacuums\015\012I changed the belt on\015\012Posted by hiphoppy69 on Apr 28 ... Vacuums
Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a
You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum
The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug
... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity
Tafel Steam Iron Model 2820 3.12 104 - switch connections - can you please explain how this is works Iron stoped workin open the back and one of cales to the switch is hanging loose - but can not workout the obvious way to reconnect - can you help by showing me a diagram of the switch mechanism kind regrad
Wiring diagram I have a replacement main switch for my vacuum cleaner. Two blue and two brown but no diagram or markings on terminals to show which wire goes to which terminal
How to Repair a VacuumCleanerhttp://home.howstuffworks.com/how-to-repair-small-appl ... VAX Appliances 2000 Canister Vacuum
Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.
Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie
My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
My dyson DC24 makes a loud noise when turned on. The air flow seems to be going out another another end on the vaccum kind of by the on switch.
Hi there,I'm sorry to hear you're having difficulty with your DC24. If the relief valve is activating, you may have a blockage somewhere in the machine, and the filters may also need a wash.To locate and remove any blockages, please f ... Dyson Ball DC24 Bagless Upright Vacuum
U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?
... Hoover U5468-900 WindTunnel Bagged Upright Vacuum
Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.
... Miele S251 Flamenco II Bagged Canister Vacuum
I have a Hoover Savvy model U8174-900.. The beater brush only runs sometimes when I pull the unit backward. The handle switch seems OK but I cannot figure out why it is acting strange like this. Tilting the handle up or down does not seem to have an effect on this situaltion. Thanks for your help. Ron Simon
The Savvy has had its problems with the switch in the handle it will need to be replaced. Don the Vacuum Doctor Alb,N.M. ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum
I was lucky enough to get a Janome 372 very cheaply at a second-hand store but it came without the manual. A friend managed to thread it so that it works but the threading is completely counter-intuitive and I'm not sure that I'll be able to remember how to do it without a threading diagram to turn to in a pinch. Unfortunately, I can't seem to find a threading diagram online anywhere! Can anyone direct me to a site that shows this?
I would look in a site called www.Pronto.com/manualsI hope this is helpful to you . ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hello! I purchased the cascade 170 internal filter for my tadpole this past Tuesday. All seemed to be well until I returned home from work this Sunday morning to find him dead. There was a film of little white bubbles all of the top layer of the water. The filter was submersed however it appeared that some of the water had evaporated but was still over the top of the filter. Is there a problem with the filter or the level of water? I'd like to get another tadpole but would like to know
I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??
... Kirby Vacuums
Repair drive I switch it to the Drive position and it is like it doesnt kick in.
Hello, nixonI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would t ... Kirby G4 Bagged Upright Vacuum
How to change the bag in the Oreck XL hand canister vac? I can't seem to get the plastic piece back in before locking with the metal clip. Is there a diagram to show me?
... Oreck Vacuums
Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin
Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum
I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.
Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums
CANISTER IS GETTING POWER BUT NO SUCTION FROM HOSE AND DOESNT SEEM LIKE THERE IS POWER GOING TO HOSE..I HAVE CLEANED OUT THE FILTER AND CHECKED ALL BREAKERS...
Hello,Carnister vacuum cleaners are all built with the same \015\012principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are ... Hoover S5615 Hush Central System Vacuum
My bissellpowersteamer clearview #3105403 strays no solution when on. the hand attachment does, I have also lost my directions and problem solving booklet to which I would like to recieve another one,
When it doesn't spray solution then that usually means that the pump belt is broken or stretched. You can get replacement belts and also view the manual here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.
Where can I get a wiring diagram for this machine? Switch seems to be bad.
... Festool CT22e Vacuum
Eureka Mod 4870. Replaced belt. Beater won't engage. Flat steel spring tensioner doesn't seem to be locked in place when selector in Carpet mode. Is there some sort of ''keeper'' that holds spring? Any diagram or picture available to show proper placement?
... Eureka Smartvac 4870 Bagged Upright Vacuum