Having problems with your Vacuums ?
How to use scunci snap and flip clip - Vacuums
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to use scunci snap and flip clip - Vacuums
The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?
... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum
I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!
I have a Dyson upright vacuum cleaner makes a helluva racket whilst in use. Called up Dyson and they told me to flip the floor/carpet knob 10 times back and forth. That did the trick for a short while and it started again. Continue attempts useing that technique does not work. I think in spite of the big bragging I see on the TV this guy braying about how superior his product is it is a piece of junk. I should have bought a Eureka or something, at least it would have been less expensive. I
Hi there,I'm sorry to hear you're having difficulties with your DC07. Your cleaner's brush control system is designed to make a ratcheting sound to warn you if the brushbar is jammed. Since you haven't been able to resolve your issue with ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The wheel fell off our bissell 16n-5 vacuum is ther a way to get at it to put the snap clip back on
... Bissell 16N5 Upright Vacuum
I have a hoover windtunnel upright vacuum, It will not shut off and I have to unplug it to do so. If I take apart the upper handle and manually flip the internal switch it works just fine, only when using the external switch on the handle, wont shut off.
This is a common problem with this machine. The switch has too much resistance to be turned on and off with the switch button and rod. If you put in a new switch, ( # 28161075 ), your problem should be fixed. ... Vacuums
When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip
Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum
When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it
My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums
I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?
Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?
I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum
I was given a Kenmore progressive hepa filter 22313 Bagged Canister Vacuum recently, but don't have the manual. We used it once to vacuum the house and it worked beautifully. Then we used it 5-6 days later and it started whining and getting hot. What year was this vacuum manufactured? Where can I download an owners manual?? Help!
Http://www.managemylife.com/mmh/owner_manuals/5461/KENMORE-Vacuum-Canister-L0809572 ... Kenmore 22313 Bagged Canister Vacuum
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a
Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr
Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I was in the middle of using my vacuum when it quite on me. I tried multiple things including letting it cool off for a while as I was using it to vacuum my car outside and it was pretty hot. I also dismantled it according to the directions and looked for blockages and didn't find any and lastly I cleaned out the brush and put it back on. I am out of solutions. The vacuum is not that old; we have only had it for a few months. Any assistance would be appreciated. Thank You, Karen
Hi the problem you are more than likely having is with the wires that go into the vacume they are not that secure and do work loose.now if you remove the cylinder that you empty, now you see where the wire goes into the back of the vac, w ... Dyson Ball DC24 Bagless Upright Vacuum
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum. Can't find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
\015\012Vacuuming Liquids\015\0121. When picking up small amounts of liquid\015\012the filter may be left in place.\015\0122. When picking up large amounts of liquid\015\012we recommend that the filter be\015\012r ... Craftsman 17765 Canister Wet/Dry Vacuum
Dirty filter caused vacuum to swtich off mid-use. Filter's cleaned, but machne won't start again. Is there reset switch or do I need to take it in to get fixed?
... Westinghouse WST1551 Wired Deluxe Upright Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums
My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.
Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums
When the vacuum is on and in the "stand up" position in oder to use the hand held part of it, the top makes a strange sucking sound that it never did in the beginning, But as soon as you use it as a floor vacuum it stops.
IT SOUNDS LIKE THERE IS AN OBSTRUCTION IN THE HOSE AND CAUSING THIS NOISE ... Dyson DC14 Bagless Upright Cyclonic Vacuum
G5 vacuum won't start (turn on) when I try to use the accessory hose. It starts (works fine) when using the regular floor brush for vacuuming.
... Kirby G5 Bagged Upright Vacuum
I recently purchased a used Featherlite bagless Dirt Devil....Everything about this vacuum is superior to any other vacuum I have had....the problem is, no manual, and I need to know how to use the hose for the attachments, where do I place it for suction?
... Dirt Devil Featherlight Bagless Upright Vacuum
Oreck Belts Why do they smell badly and almost always break when being used for an extended period? I see Mr. Oreck in print, television and internet ads -- and he certainly carries himself as a credible person; a man you want to believe....But reading his biblliography -- he started his career (in this area as I know it) as a "Vacuum Cleaner Salesperson" for Whirlpool. Many vacuums brands - particularly those that are noit sold directly by retailers (Oreck, Kirby and others) use the commission-
Unfortunately this is a very common problem on the Oreck XL uprights. As you you noticed, there is even an extra belt storage on the machine itself, on the bottom plate. When a vacuum cleaner has to put an extra belt on the machine ... Oreck XL2200 Bagged Upright Vacuum
Shutting off my vacuum has been shutting off in middle of use and i dont know why its like its over heating and i cant use it again for almost an hour is there a solution to this? or do i need to get a new vacuum?
It has a built-in temperature sensor which prevents it to be damaged from overheating. That's why it shuts down. It just needs to be opened up and cleaned thoroughly. Start with the hose if it has one and let someone who is handy with electric applia ... Vacuums
My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing
No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum