Having problems with your Vacuums ?
Wires burned up to the stator coil to my jd lt155 i need a wire digram
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Wires burned up to the stator coil to my jd lt155 i need a wire digram
Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n
From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums
I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)
The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum
Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.
Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums
Need a wiring diagram for a karcher puzi 100 yellow. Mainly need to know which way round the wires go on the switches?
Need proper wiring connections inside unit, where they have pulled apart from squeeze connectors.(Wiring diagram needed) Can someone E-Mail this to me? Fritz (an ''old'' mechanic) Folks I have talked to, say there is no specific model number for these units. They are just described by name, and serial #. and I have relayed exactly what was labled on the unit. Please post this and quit asking me to enter a "valid" product.
Fritz , thanks please confirm... there are likely more than 2 leads from the motor?? I have not seen or worked on the Tristar CXL as it is very new.You will have a high low function but: Should the power head function at both spee ... Vacuums
My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks
Place the coil in the hole and turn untill reach the desired height. ... Vacuums
I took my durabrand toaster oven model t0-80 apart and i need the wire diagram to put wires back on it cause it needed cleaning.
Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?
They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums
Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?
Need to replace power cord on Hoover windtunnel need wiring help
Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum
Hi, I have an old 2 wire chandelier I would like to make a plug-in. I have bought the wire swag kit to change it, but the chandelier wires are unmarked. Both wires are copper and I cannot see an insulator on either side...I need help!! Thanks!
Can you determine some way of telling which wire goes to the center conductor on each of the lamp sockets. (That particular wire,-- however it is identified-- (Maybe a tracer thread? in the woven ins ... Vacuums
Rowenta Effective Steam Iron DX1700 Need wiring diagram. How do I wire the power cord to the internal Red, Blue, and White wires? What wires are neutral and which are hot?
I need to wire the switch to my coleman 2234 push button 12v water pump in my camper trailer. it is wired to the battery now with the "red" connected through a small fuse. i just cant figure out where to wire the on/off switch to.
Hi there. When connecting a switch, it is important to remember that a switch will only "break" the positive (+) circuit, while the neutral wire will go directly to the battery. So, basically split the red wire coming from your pump and connect the s ... Coleman Vacuums
I need to know how to hook the wires up to the start switch. There are two wires from the external cord and two wires from the internal cord.
White wire to neutral black wire to hot if you post colors I could help you red ,orange, black,pink, blue, or violet are usually hot guessing a striped wire is usually neutral please post colors ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals
Wiring diagram Need wiring diagram for the motor wiring.
\015\012\015\012HI, tell me is this you want,, \015\012\015\012Gunjan:-) ... Vacuums
I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?
... Kenmore 34722 Grab-N-Go Upright Vacuum
The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.
Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum
Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you
Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums
Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks
... Kenmore 23313 Whispertone Bagged Canister Vacuum
I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.
I need the wiring diagram for the motor.
... Hoover Commercial Windtunnel C1705-900 Bagged Upright Vacuum
The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available
Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums
I need a wiring diagram for the shark mop a wire came loose but can't find out where it goes ???
... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum