Having problems with your As Seen On TV Swivel Sweeper Vacuum ?
Swivel sweeper brushes slow with full charge even after cleaning brushes
When you say you cleaned out brush's are you talking about the build up between the bristles? I've found that I have to take the roller completely off and use fine needle nose tweezers to actually get all the stray hairs and caked on dirt as it hides close to the inside of the brush rollers. It's a bit more work to do this but I think you might benefit from this extra step!
Repair Help & Product Troubleshooting for As Seen On TV Swivel Sweeper Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Swivel sweeper brushes slow with full charge even after cleaning brushes
When you say you cleaned out brush's are you talking about the build up between the bristles? I've found that I have to take the roller completely off and use fine needle nose tweezers to actually get all the stray hairs and caked on dirt as it hi ... As Seen On TV Swivel Sweeper Vacuum
Swivel sweeper slow even after cleaning brushes
... As Seen On TV Swivel Sweeper Vacuum
My swivel sweeper battery will not hold a charge. The light is always red. I even bought a replacement battery -- same deal. Do I need to replace the charger also?
... As Seen On TV Swivel Sweeper Vacuum
Roomba give message to clean brushes even when I have cleaned brushes, wheels, and anything else I can find. It will only clean about 3 minutes.
Pull 2 roller brushes off.remove funny lookin yellow ends clean hair ect. also pop out front wheel and clean ... iRobot Roomba 560 Robotic Vacuum
Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!
Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum
Water and cleaning solution not dispensed when pressing the switch. Heat light is on, water and solution containers are full, brushes and vacuum working. Selector is on floor clean and not brush clean.
Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Wont charge new roomba for xmas. lights on charging unit both flashing but no power in roomba. it worked yesterday when i got it out of the box and did a full clean. i feft it on charge over night ready for the clean today but when i got up no power atall please can you offer a solution. i have held down pock and start - no joy. i have checked the battery connections - no joy please help many thanks caroline
Did you try plugging in 560 driectly to charger then run it? ... iRobot Roomba 560 Robotic Vacuum
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums
Our Roomba 530 stops after few minutes saying clean the brush ,even after brushes are cleaned.
FIrst, remove the dust bin part and the brushes. Then, there are four\015\012screws on the bottom gray panel which have to be removed first in order\015\012to get to the gears which hold the brushes. I did not remove the little\015\012sweeper brush o ... iRobot Roomba 530 Robotic Vacuum
I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i
Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums
I have a Bissell proheat clearview 12 amp 5 cleaning rows of dirtlifter powerbrush. It won't shoot the cleaner to the brushes. I cleaned the filter, checked the belt, water is full, and soap dispenser is full. Still no soap going to rug. Can you help? Thanks
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano
... Electrolux Vacuums
Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.
Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums
IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.
It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum
Dust buster won't hold a charge, even if I let power run down to nothing and then charge it for a full day or two. This is the 2nd dust buster that has done the same thing. When I first take the item from the charger, it appears to have a very strong charge. Then within a minute, I cannot pick anything up. Thanks for your help.
... Black & Decker AV1200 DustBuster Handheld Vacuum
Agitator brushes wont turn even after cleaning
The brushes will not turn even wen the switch is turned on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I bought a roomba pro elite robotic floorvac at a tag sale from an elderly couple who apparently used this vac very little as it was very clean and she had never even used it enough to use the extra filters that came with it, she said it was just too much for her to bend down to work it or move it. i suspect she stored it but kept the battery in it. after charging it, it powers up and sings a little tune, but then shuts off. i cleaned everything, including the sensors. it still shuts off, do you
... Roomba Pro Elite Bagless Robotic Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
High pitch My Hoover fusion vacuum cleaner began making a high pitch sound that makes it very annoying to vacuum. I cleaned all the things I could clean. I even cut out all the hair that was entangled in the brushes. Any idea what is causing the sound. It sounds like an siren is going off.
The Hoover Fusion has design flaws in the motor, including a metal plate that is too thin to contain the forces acting on the motor, particularly the constant strong tension from the drive belt, and a plastic plate that is attached to the metal plate ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
Brushes won't turn remain motionless as if cleaning hard floors even though button depressed could it be a problem with the brushes or button still under guarantee
There is a re-set button located on the brush head on the left side as viewed if you are standing directly behind the vacuum cleaner. It is black in color and is recessed slightly into the cover of the brush cover. It is round and about the size of t ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?
DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The brush on my bissell helix (model 22C1-2) stopped working all of a sudden today. The hose still sucks and everything. I even cleaned the spinning brush and it still doesnt work. I just bought it in August.
Why does our Roomba says there is a problem with the brushes even after they have been thoroughly cleaned? It will run a minute maybe then tell us there is a problem, check brushes.
You need a new battery if you have done the battery reset,and then leave the unit on the charger for 16 hours straight if the problem continues after the charge you need to get a new battery ... Vacuums