Having problems with your Beam 050814 30ft Hose Square Grip Q100 & Solaire Central Vacuum ?
Beam q100 roller bound up, motor won't run, light don' t light
Repair Help & Product Troubleshooting for Beam 050814 30ft Hose Square Grip Q100 & Solaire Central Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Beam q100 roller bound up, motor won't run, light don' t light
... Beam 050814 30ft Hose Square Grip Q100 & Solaire Central Vacuum
I have a progressive 35923500. roller motor runs but blower motor doesn't even try to start. Intelliclean lights light but headlight does not light.
Is this issue resolved now that the nub was pressed and it runs fine? ... Kenmore Vacuums
Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..
The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?
As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.
... Sebo Automatic X1 Bagged Upright Vacuum
Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???
Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see
... Oreck XL Ultra Bagged Upright Vacuum
I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.
The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum
I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions
Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum
Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down
... Eureka Vacuums
Question mark light has come on my vacuum and it wont run. I replaced the bag, but it wont start. I don't have a new filter is that the problem?
... Electrolux Vacuums
DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN
Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The motor is running, the roller brush spinning rubber smell
The belt may be stretched replace it ... Vacuums
Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?
It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I was using my Heritage 11 vacumn with the hose attachment and the motor shut down like the power went off .When you push the switch on the housing the light comes on but the motor does not run.
Hi, the motor could be overheating. Most vacuums have a heat sensor that shuts the vac. off if there is a clog. Let it sit, feel if it's hot. If so you may have a blockage of dirt etc. Try to clear it, let it cool and tart it up. I hope this helps, i ... Kirby Heritage II Vacuum
Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt
... Bissell 21K3 CleanView Helix Bagless Upright Vacuum
The motor runs slow (so does not pick up properly) and does not run at all if the hose is pulled out. There doesn't seem to be a blockage and the roller is clean. Could it be as simple as changing the filters?
... Sebo Felix Ice Blue Bagged Upright Vacuum
Lux legacy my vacuem wont run but 1second after i push the on switch. the full bag light comes on when it shuts off.i turn it on again and it runs for asecond and cuts off. it has abrand new bag in it.i tried adjusting the suction knob on top to no avail.
Actually the problem is inside of the canister itself. You need to change a part called the control valve. Occaisonally when fine particles get inside of the valve it damages the inside of the valve, sending a false reading to the main motor, causi ... Electrolux Lux 7000 Bagged Canister Vacuum
On my dyson dc 28 the carpet cleaning bar turns easily by hand, but does not turn on when the cleaner is reclined from the upright position. The white light illuminates when preseed, but the red light does not illuminate even though the motor is running. Thanks
... Dyson DC28 Animal Bagless Upright Vacuum
Dyson DC04 hello, my dyson seems to run ok in upright but when i tilt back the motor sounds like it is struggling, do you think it's down to the rollers being to low and can you adjust height of rollers to overcome said problem? yours chris
Hi.\015\012\015\012If the motor is struggling check to see how easy it is to rotate brush by hand it is stiff to rotate the bearings in the roller may be siezed or the roller could be clogged with hair etc check it & let me know what ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
We replaced the motor and the overheat light stays on and the motor does not run. Any suggestions?
Sounds like a bad thermal switch to me. take it a vacuum shop they should be a able to rewire it for you. ... Electrolux Epic 6500 Vacuum
We have a Beam Millinium 199G built in. the function light was solid red so we replaced the motor. How do we reset the light to go green?
Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.
The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum
Sharp TC-4650 vacuum motor does not come on but the light does. waited a day and it ran again but when i unpluged it and plugged it into another receptial themotor did not run but the light can on
... Sharp Twin Energy EC-T4660 Vacuum
SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.
... Sebo X4 Bagged Upright Vacuum