Having problems with your Beam Industries Vacuums ?
Correct brush roll replacement part for a Beam #BM1383
\015 BM1383 type L\015
Repair Help & Product Troubleshooting for Beam Industries Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Correct brush roll replacement part for a Beam #BM1383
... Beam Industries Vacuums
I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.
I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum
Hoover Bagless Hello, My Hoover bag less (Model U5280-900) is not picking up dirt like it should. The brush roll is spinning fine, but the bristles on it are only about one quarter inch long. I am wondering how long they should be. The vacuum is quite a few years old. Do you think it is time to replace the brush roll. Could you email me at [email protected] about this topic. The product bar below did not contain my model no. The correct model no. is above in my message. Thanks
If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]
You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums
Brush roll i am trying to find and purchase a new brush roll for my ge vacuum. The number on it says that it is 106585 and from what I can tell that is the same as 5550 parts. Is that correct?Thank you
I have the same vacuum for the last 5 years. I dont know if its the same as 5550 (I assume it isn't) but I can give you the part number 61445-1. It costs around $16 and you can call 1-877-207-0923 b/w 7 am and 8 pm Mon-Fri central time, o ... GE 106585 Upright Vacuum
I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile
... Eureka Smartvac 4870 Bagged Upright Vacuum
I am trying to find the powermate parts to replace the roller brush on this vac I have trouble finding websites that sell these. I need to know the item numbers so that I can order the correct items to fit this model.
Brought the powermate part to local Sears part store and they ordered the items we needed \015\012 thanks for trying to help \015\012\015\012GFreckles913/Glenna Rodell ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom
... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum
Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus
... Bissell 6595 Lift Off Bagless Upright Vacuum
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.
Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Agitator brush roll needs replacement
To change the beater bar you would need to open up from the bottom.To get the parts you would need to produce the model and serial numbers to your local hoover dealeror cheak on the internet for your closet dealer and order the part.There not to bad ... Hoover U8143-900 Upright Vacuum
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
I have the Polti Vaporetto model VTT 2085 FIE 74, year of manufacture 1998; my son managed to lose the large brush. I would like to purchase a replacement large brush and also the round brush for the 120 degree C jet nozzle. I also want to buy some cotton cloths for the large brush and for the small brush. Where can I obtain these parts and cloths?
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Brush will not turn on on my Bissell Healthy home vacuum, the brush button is depressed and brush is clear. The vacuum motor works fine, just the brush will not turn on. Is there a part to replace?
... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
How to replace Simplicity vac brush roll strips?
The caps will come out of the end of the metal roller. They can be difficult if it's been a long time as dirt and grime can build up. Try sticking a flat head screwdriver in and gently twisting to get the caps to slide out. ... Riccar Vacuums
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://220.127.116.11/v/u6451900.pdf ... Vacuums
Replace dyson 07 animal brush roll assembley
The end caps of the brush assembly which contain the bearings are only a push fit onto the spindle (quite tight). Remove these and the brush bar will pass through the drive belt loop. To achieve this the belt has to be stretched slightly so care has ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hoover WindTunnel U6433-900 brush roll control broken off
I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums
I caught a shoe lace in my Dyson DC17; pulled it free, opened the brush/roller area and cleaned everything but the brush still won't work. Read somewhere that there is re-set button but the only one I found was to switch between the brush / sweep functions. Is there a fuse / connection / part that may need to be replaced?
I don't believe so. Keep trying the reset button. Sometimes the reset sticks. Hope this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The plastic drive for the roller brush on our dc25 animal is stripped out.it screws onto the motor shaft.does this part come with a replacement roller brush?
... Dyson DC25 All Floors Bagless Upright Vacuum