Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?
Smart mix what is the trick to connecting the smart mix?
Glad you did.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Smart mix what is the trick to connecting the smart mix?
Glad you did. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Connecting a BISSELL AUTO MIX PISTON TO A AUTO MIX KNOB
Take of the housing ,turn it over and you will see the under side of the auto mix dial , Then turn the auto mix dial to rinse only;\015\012On the top of the piston you will see a small slot , this fits into \015\012the out ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell proheat pro tech model 7901-3 smart mix dial and valve assembly
Turn the knob to the water only, put the piston on the bottom of the knob then turn it slightly so it doesn't fall off, Start to put the cover on, when it is straight, turn the knob to the water only selection and push the top all the way down. The ... Vacuums
Replacing Smart Mix knob
The knob itself will only go in one way, What I was talking about is when you put the top cover back on, the knob should be in the water only position. This way the piston (on the bottom of the knob) will go into the slot correctly. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Cleaner solution in smart mix tank not mixing with the water from the bladder. All tanks are seated properly
... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
The solution in my smart mix will not mix with water and the button just keeps going round and clicks and will not stop on either water or solution.
The smart mix knob is connected to a piston that slides up and down into the automix assembly. This piston has come off of the smartmix knob and left the unit on water only setting. Sometimes the smart mix knob breaks on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG
It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..\015\012\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
Smart Mix selector
I figured it out,since you nor Bissell was of no help. It turns out to be quite easy. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Smart mix valve reassebly and alignment
Have the piston on the screw threads, put the knob on the water only setting, then after the piston is on, turn slightly so it doesn't come off, just before you put the housing all of the way down, turn the knob back to the water only setting and the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell proheat 1698 reassembly, smart mix piston, new pump?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Replacing smart mix plunger bissell proheat model 7901 procedure for proper installation
Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?
Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum
How do I replace the Smart Mix knob on a Bissell shampooer
... Bissell Vacuums
I have 1699-R Proheat carpet cleaner recently I was replacing the food pedal during the process some tubings that carry water/chemical got mixed to the point that one side instead of spraying chemical sprays only water from oneside the other side that is connected to the flow indicator cap is completely dry does not move at all. I am looking on line to see tubing diagram for model 1699-R
The instructions in this Repair Guide pertain to the Bissell PowerSteamer ProHeat (#1698)\015\012and the Bissell ProHeat ClearView(#1699). \015\012If your unit matches this model numbers then the repair guide plus diagrams for this unit is mentioned ... Vacuums
I have Bissell Model 1699-R Proheat carpet steam cleaner one of the tubings that connects into spray got mixed with some tubings during tubing replacment to the point that tubing that is conected into flow indicator cap does not turn at all to show if the chemical is sprying or not.i am looking mainly for tubing water/chemical diagram in order to verify the right connection.please help if you can bissell user. thanks
Broken Smart Mix Dial-How to replace
You will have to remove the top, the knob screws on but has a stop tab. Is the plastic below the knob ok, if not then you need to replace the top cover. After you replace the knob, then put the piston on from underneath, have it set to water only s ... Bissell 7950 ProHeat Upright Wet/Dry Vacuum
I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the
I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums
Smart Mix Dial - Reassemble Cover
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac
There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums
Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh
The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact
Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum
The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-
... Bissell 8910 ProHeat Clear View Upright Vacuum
Smart mix plunger bissell 1699
This is what happened to me. The heater had to be cleaned. Easy fix. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.
First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum
Flow indicator is not turning and the water from the bladder does not spray out only the smart mix container emties
... Bissell 7950 ProHeat Upright Wet/Dry Vacuum