Having problems with your Bissell 3576 CleanView II Bagless Upright Vacuum ?
Bissell brushes only turn in upright position
The brushes always turn on this unit, therefore the belt is probably stretched out to the point that there is no tension. When the unit is reclined the brush is probably stopping on the carpet as the unit drops slightly to the surface it is on. I recommend replacing the belt. You can find it at this link: http://www.bissell.com/parts/?sc=part&productid=2421&partid=4680&cid=ccsocial
Repair Help & Product Troubleshooting for Bissell 3576 CleanView II Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.
... Bissell 9400 ProHeat Upright Wet/Dry Vacuum
Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.
Here is some information about a second Auto Cut-Off Switch near the power switch:\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is mo ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Bissell brushes only turn in upright position
The brushes always turn on this unit, therefore the belt is probably stretched out to the point that there is no tension. When the unit is reclined the brush is probably stopping on the carpet as the unit drops slightly to the surface it is on. I r ... Bissell 3576 CleanView II Bagless Upright Vacuum
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Eureka 4870 brush won't stop turning in upright position
There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?
Things to check are the cord, switch, and the motor. ... Vacuums
Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position
I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums
Brush roller does not turn off in upright position
Make sure there is not a lever to move in order to stop the brushes/agitator...\015\012if the belt makes contact with the end of the shaft the brushes will rotate...\015\012tighten all of course/and take the panel of to check behind the b ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge
Brush roller does not turn on bissell upright
Pull the brush out and pull the bearings off the ends. Clean everything up with rubbing alcohol. Put it back together. DO NOT OIL the bearings. Oil will make dust stick and jam the bearings again. ... Vacuums
My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?
This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums
I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?
Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell 4104-w brush not turning - Bissell 4104 Bagless Upright Cyclonic Vacuum
... Bissell 4104 Bagless Upright Cyclonic Vacuum
Bissell 82H1 vacuum brush won't turn - Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Bissell 82H1 Brush won't turn - Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
My bissell brushes are not turning - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.
I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?
Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Brush won't turn. - Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Is the grey "brush" button on the handle depressed? Brush won't turn unless the button is down ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Brush won't turn - Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
Remove the bottom plate and check the belt for breakage. If it is, it will need to be replaced. Remove the brush assembly and check the end bearings for debris accumulation. Clean the brush bearing ends and the bearing interiors. Re-lube with 3-1 oil ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
Brushes do not turn /model9200 - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Brush not turning and no suction - Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
BRUSHES DO NOT TURN - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
It sounds like the belt came off, if it did it will be a simple fix. All you will have to do is put the belt back on and you will be good to go. If the belt is broken write down the make, model and take the belt with you a head to like walmart and se ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum