Having problems with your Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum ?
How to remove bottom plate
\015 The vacuum has some type of allen wrench looking screws, but non of my wrenches fit. Is there some special tool I need to get in to replace my belt?\015
You will need either a t15 or a t20 torx bit. you should find these at any hardware store.
The Healthy Home vacuum has 6 t20 screws on the bottom plate, careful though as two of them are set fairly deep near the wheels and will require at least a 4 inch long t20 to reach the screws.
Repair Help & Product Troubleshooting for Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to remove brush roller bottom plate
Make and model ?????? ... Vacuums
S2220 Flair Bagless Upright Vacuum: how to remove bottom plate...
... Hoover S2220 Flair Bagless Upright Vacuum
Can't remove bottom plate to change broken belt on oreck xl instashield vacuum ...i think i removed required screws
... Oreck Vacuums
We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.
I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked. ... Vacuums
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How do you remove bottom plate of the shark navigator vacuum
... Shark Navigator Bagless Upright Vacuum
How to remove bottom plate
... Hoover Encore Supreme Energy U4293-930 Vacuum
I have a Fuller FB80 and am unable to remove the bottom plate for cleaning. I can only find 2 screws holding it on, but I'm afraid to force it in case I might break the plastic.
... Fuller Brush FB80 Bagless Upright Vacuum
My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.
Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums
How to remove bottom plate
You will need either a t15 or a t20 torx bit. you should find these at any hardware store. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Belt How do you remove the bottom plate to replace the belt. I have the brush off but can't figure out how to get to the other end to loop the belt
You need to take the top cover off to get to motor shaft. Some had a couple of screws from the bottom, others had tabs, use a flat blade screwdriver to fit into the slots at the bottom edge of the top, pry out and up to pop the cover off. ... Hoover Commercial C1403 Bagged Upright Vacuum
How do you remove the bottom plate, in order to install a new belt?
On the top of the base right behind the bumper you will see 1 screw on both sides.take those out and lift the cover off ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My dyson DC07 upright vacuum makes a loud noise when I turn on carpet mode. I removed he bottom plate and checked the belt and it looks ok
Did you check the roller brush to make sure it was clear of debris? ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My Eureka model 2961 does not **** up larger particles. You can see it picks up dust and dirt. Am trying to remove bottom guard plate to check belt but can't take it off.
Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Eureka 2961AVZ Bagless Upright Vacuum
How to remove the bottom plate to install a new belt ?
Here is the owners manual for the machine in question, It has all the info you will need to change your belt. MANUAL ... ELECTROLUX Commercial Upright SANITAIRE DURALITE UPRIGHT VACUUM Each
Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.
... Eureka Sanitaire S661 Bagged Upright Vacuum
How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?
... Simplicity 7850 Premier Bagged Canister Vacuum
I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.
If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums
I want to replace the belt of a proline uvc18 but cannot remove the bottom plate
... Gateway Vacuums
How do you remove the bottom plate to get a the belt for the roller
Have a look at the top cover you shuold have some screws in it remove them and lift off the cover to get to the bottom brushes ... Hoover Encore Supreme Energy U4293-930 Vacuum
The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.
The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum
I have an old elna - elnita air electronic zz, i have lost the user manual and have got thread jammed under the needle plate which I can't remove. How do I remove the needle plate so that I can try and remove the thread? There are what appears to be 2 screws except they are smooth i.e. no **** or cross in the top to unscrew them.
I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.
The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.
Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum