Having problems with your Bissell 8910 ProHeat Clear View Upright Vacuum ?
Brush assembly won't spin
\015 Hi. The brush belt connects at one end to the brush assembly and at the other end to a small toothed wheel with a short shaft that fits into the motor assembly. This small toothed wheel popped out and I can't get it to stay in place.Every time I fix it & put it back together, it pops out again when I turn the machine on.Any suggestions?\015
You must replace the pump thats what the belt is attached to
Repair Help & Product Troubleshooting for Bissell 8910 ProHeat Clear View Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My Dirt Devil Model 088520 has a brush assembly that wont spin. How can I either change the bearing or free it up somehow? I have been searching for a new brush assembly part number 2860145000 but it
Try this link > http://dirtdevil.com/parts/category/brushrolls-uprights/ ... Dirt Devil Vacuums
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and
The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t
Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.
The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?
... iRobot Roomba 530 Robotic Vacuum
I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?
Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My hoover spin brush steam vac brushes wont spin
Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums
Spin brushes wont spin and the switch wont turn machine off. I have to unplug it.
For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum
Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther
... Clarke Vacuums
DC07 brush wont spin on bottom, took all apart and wont work
Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.
Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum
THE BRUSH WONT SPIN AND THE SOLUTION WONT COME OUT
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Brush assembly will not spin at all.
The turbine is bad, that is what drives the brush roll. You either replace it, sometimes you can take the turbine apart and clean it, alot of times they just get gummed up and won't work. Number 23 is the turbine. ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum
Brush assembly will no longer spin on carpet however the suction from the system is still good. Unit is only 5 years old.
Probably a seized beater roller (the bearings wear out). Just order the new part and replace it and you'll be one your way again. And of course maybe a belt. ... Electrolux Centralux Vacuum
Brush wont spin
Was the belt worn or broken? It probably needs to be replaced. Here is the belt you need:Dyson DC07 Belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin
The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
Beater brush wont spin for the hoover pet rewind
... Hoover WindTunnel Pet Rewind Upright Vacuum
Brush wont spin, belt is perfect
It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum
The brush bar wont spin on my dyson dc 25... i
Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow
Brush wont spin on my bissell 93z6
... Bissell Heavy-Duty Vacuum Cleaner, 93Z6
Dyson DC 28 brush bar wont spin
... Dyson DC28 Animal Upright Vacuum New DC 28 Animal
Brush assembly won't spin
You must replace the pump thats what the belt is attached to ... Bissell 8910 ProHeat Clear View Upright Vacuum
No suction power ,brush wont spin on carpet power nozzle. When it
You need to replace the belt that turns the brush. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
The spin brush wont spin but the water is spraying out and sucking up
Possibly the brushes need cleaning http://www.hoover.com/pdfs/manuals/F5914900.pdf manual for your steamvac Press all four latches (B) and pull brushblock out. The brushes can be cleanedunder running waterGodbless ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum