Having problems with your Bissell Heavy-Duty Vacuum Cleaner, 93Z6 ?
Brush wont spin on my bissell 93z6
\015 Brush wont spin. have looked for something tangled but can find nothing\015
Repair Help & Product Troubleshooting for Bissell Heavy-Duty Vacuum Cleaner, 93Z6
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Brush wont spin on my bissell 93z6
... Bissell Heavy-Duty Vacuum Cleaner, 93Z6
Bissell powersteamer clearview model 8806-roller brush wont spin
... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?
Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My bissell cleanview helix wont **** up anything on carpet. the brush doesn't spin. any thoughts?
... Bissell Cleanview Helix Deluxe Bagless Upright Vacuum Cleaner 21K3
Model 2090, bissell quicksteamer brush wont spin
... Bissell 2080 QUICKSTEAMER Upright Vacuum
Brushes wont spin, how do you replace belt - Bissell 9200 Upright Vacuum
Hey, sorry to hear the brushes are not turning. Here's a quick link to instructions on how to change the belt(s). We also have a terrific How-to-Video linked to this also. \015\012 ... Bissell 9200 Upright Vacuum
I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brush bar wont turn, Bissell smells like burning rubber
The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun freely, or is one of them froze up, if so replace the brush roll. If it is ok, try to turn the brush roll by hand, maybe the belt got pinched and won't move. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?
... iRobot Roomba 530 Robotic Vacuum
I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?
Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.
- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum
My hoover spin brush steam vac brushes wont spin
Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums
Spin brushes wont spin and the switch wont turn machine off. I have to unplug it.
For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum
I have the bissell powerglide vacuum with the turbo brush attachment. Being the neighborhood "cat lady", I love this attachment -- that is, I did until it just stopped spinning. I don't see anything blocking the brush. It just doesn't spin when I attach it to the vacuum hose.
1. this could be (2) things that are happening or 32. there is hair surround the spindle (rotation) brush tool blocking rotation or you have a motor that has failed and it is not turning the rotation brush.3. the switch (on /off) has fail ... Vacuums
DC07 brush wont spin on bottom, took all apart and wont work
Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the
Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums
THE BRUSH WONT SPIN AND THE SOLUTION WONT COME OUT
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Brush wont spin
Was the belt worn or broken? It probably needs to be replaced. Here is the belt you need:Dyson DC07 Belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?
Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums
Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.
It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft ... Bissell 9200 Upright Vacuum
How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin
The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum