Having problems with your Dirt Devil M086700 Vision Bagless Upright Vacuum ?
I cant remove the houseing off the bottom of the motor can someone plz help
Start by taking the bottom off and remove the brush roller and belt.go back to the top and on each side of the upright where it meets the base you will see 2 plastic covers that are held in by screws take those out and that will disinguage the upright from the base.next you will see screws on the front and on the back of the motor housing,take those out.on the back right above the pedal you will see a screw take that out.right below that is the intake hose thats held on by 2 screws,take those out you should be able to open up the motor housing
Repair Help & Product Troubleshooting for Dirt Devil M086700 Vision Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I cant remove the houseing off the bottom of the motor can someone plz help
Start by taking the bottom off and remove the brush roller and belt.go back to the top and on each side of the upright where it meets the base you will see 2 plastic covers that are held in by screws take those out and that will disinguage the uprigh ... Dirt Devil M086700 Vision Bagless Upright Vacuum
Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!
Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum
Malfunction 8 franke flair. I have removed the brewing unit o rings to free up the drive. Drive motor keeps over running the top and bottom limits hence gears grinding. Could it be the sensor on the back of the motor? What is it measuring? Any help appreciated
Doesn't work Our home was built and finished in August 07. The central vac doesn't work. There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up. Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit. Where can I get someone to help us? Or, is there an installation manual I can download to see if the builder did it properly. He stole our solar heater for our pool and s
Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum
Kirby Heritage II Replacing the Motor in the housing HELP!
... Kirby Heritage II Vacuum
I cant figure out how to remove the housing cover
Hello,\015\012\015\012Here's an excellent video showing you how to replace the clutch on a Dyson vacuum cleaner. It's a moderately difficult repair, but this video really helped me the first time I had to do this repair. I hope this he ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb
Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums
Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.
Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?
Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum
MOTOR LOUD HOW DO I DISASSEMBLE MOTOR HOUSING TO LOOK AT MOTOR. TOOK OUT SCREWS ON BOTTOM BUT CANNOT GET TO MOTOR.
... Hoover V1 SteamVac SpinScrub Vacuum
Nutone model cv-350 vacuum motor will not shut off. I have to unplug system in garage. I disconnected wire to house vacuum inlets and motor is still running. There must be a reset on the motor. I have turned the external switch on and off and still no help.
Mine is the same, and it is the relay welding itself closed. The relay is switched by the low-voltage wiring that connects to the vacuum outlets, and it switches the motor on and off. Mine was welded in the energized position. I have cleaned and file ... Vacuums
I finally removed the motor how do i strip the bottom casing
Hi Zubair. You may want to contact one of our Authorized Service Centers for assistance with the motor. Here's a quick link to assist you in locating one in your area: ... Bissell 1672 BIGgreen Wet/Dry Vacuum
Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.
... Black & Decker Black Decker Bagless Canister Pet VacVacuum
I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!
... Miele S7210 Bagged Upright Vacuum
I have to go into the garage to turn on the motor on the tank and to shut it off. When I plug the hoses into the outlets in the house, it doesn't turn on the tank motor. I don't know what part to get and nobody in Raleigh, NC shops can help me.
Is this Electrolux that's now known as Aerus? If so, take it in to the Aerus Electrolux store for a tech to look at. You can find the nearest Aerus Electrolux store by following the instructions on the site at bottom of page.\015\012\01 ... Electrolux Central Vacuum
We have a Eureka 71B Hand-Held Vacuum and it looks like the belt broke. I removed the two screws at the bottom that should release the housing that holds the belt. However, the housing still does not come apart. Any advice? Thanks.
There's a 3rd screw hiding underneath a plastic shield. You'll have to drill or cut off the covering but then it's pretty easy to deal with. ... Vacuums
Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???
Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum
How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off
I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!
I'LL DO A SEARCH ON LONE BUT THE MODEL NUMBER WOULD HELP ... Vacuums
WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.
It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum
Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?
Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums
I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.
Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum
Dyson dc04 I have just stripped machine and found the drive belt from the motor snapped. How do I remove the clutch assembly from the housing? I have removed the 2 screws but the yellow knobs are still in place.
Hi,\015\012\015\012Go to this site for manuals to help with your Dc14.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris. ... Vacuums