Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?
Dyson DC7. Problem:- switch the hoover on and it cuts out after approximately 1 second. Any ideas please?
Sounds like the motor is shot. However, try the filters first in case it is just blocked.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Dyson DC7. Problem:- switch the hoover on and it cuts out after approximately 1 second. Any ideas please?
Sounds like the motor is shot. However, try the filters first in case it is just blocked. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson DC07. Problem:- switch the hoover on and it cuts out after approximately 1 second. Any ideas please?
The motor has a built in over-current trip to protect itself (and you if it seriously overheated and caught fire). This normally automatically resets itself, however if the motor has just about had it, the moment it is switched on, it just trips agai ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Switch Problem The red switch to put on wont stay on the motor runs but as soon as you release your finger from it the motor cuts out. what do I need to do to make it work as it should?
It sound like the switch is loose if you are able take the handle apart and plug the leads back into the switch. be sure to unplugit ffirst ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hi, our Dyson cuts out after about 60 secs. We've checked all the filters plus, having read that if it works without the vortex then the problem's there (it did work) we're still none the wiser because having dismantled the vortex as much as poss, there don't appear to be any problems - any ideas?
That dyson is a old model. they don't sell it in stores anymore and the motors on dysons are made cheaply. take it into a vacuum shop. or just get a new one ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!
My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?
Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
O.k. this is the 3rd time I'm writing this...not even sure how many times I'm being charged.... Already aggravated and exhausted so Please, Please help me. I bought 2 Westek 1 outlet timers for our Bearded Dragons. They have to have 12 hours each of specific lighting (day and night). I get the "up" are off times and the "down" pins are on times. The problem is the Clock Isn't working.... Any ideas??? I'm about ready to throw them out the window except we're leaving early in the morning and
There is no money indication on this one. I'm speaking for free, so I hope you're asking for free.\015\012\015\012\015\012Oh yea, I already answered this question.\015\012You bought two bad timers!\015\012\015\012Sorry. ... Vacuums
Makita 440 Dust Extractor - Trying to rectify a problem, when i switch on an appliance plugged into the socket, it will not run. IS used to run with this plugged in, but the hoover motor runs no problem. Any ideas what might be amiss, or where i can get a wiring diagram? Thanks in Advance!
... Makita 440 Wet/Dry Vacuum
Paul, I have samer problem with SEBO X4 height adjuster. Please can you explain to me where to locate the reed switch and magnet.
... Sebo X4 Bagged Upright Vacuum
I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?
Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum
I've been vacuuming and my Dyson Animal (serial #112USE1564) keeps stopping. I checked for blockage, and none, should I have it looked at for a bad thermal cut-off switch? Please e-mail an answer to my e-mail address([email protected])ASAP!!
Hi there, I have experienced this myself and found it was the thermal cut off switch. Usual symptoms are running for a few minutes and then suddenly stopping, leave for a while and turn back on. I am sorry I cannot email to your personal addresas as ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have 2 mood lights (90843C - 925600010602) within 2 weeks of each other, when switched on they light up for under a minute and then go off. I have tried them in various sockets around the house to ensure it isn't a problem with the socket. Any ideas ? Thanks, Jan
My polti vaporetto steamer 2200R - the switch to release the steam won't turn. Have you any ideas please?
Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike
Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums
Hi i have got a Dyson dco4 it switches on but the roller doesn't go round. I have checked the belt which has gone so I have no idea what else it could be please could you tell me what else it could be
If the belt is gone, then you need a new belt. Otherwise, ensure floor select switch is set to ON.\015\012\015\012If you don't have a user's manual, you can use the below site to get one free.\015\012 ... Dyson Vacuums
I have a Morplan Vitesse 1600w steamer. When switched on the steamer doesn't heat up, only a red light flashes on the steam level lights. Any idea what could be the problem?
Check the water lvel in the steamer, if there is water then take the unit to a repair shop for a checkup. ... Vacuums
I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.
... Craftsman Vacuums
I have a Electrolux Epic 6500 SR canister vacum cleaner. It is nine years old and for the past few weeks it has started shutting off for no apparent reason.The symbol for bag change lights up and it cuts off, but even after I have put a new bag in, it still does the same thing. Do you have any suggestions? There is a little button or switch that the top of the bag fits on. Do you think it could be the problem?
Your machine is probably clogged, look through the wands, look in the bottom attachment, to see if there is anything stuck there. You can also drop a marble through the hose itself to see if anything is stuck there as well. To unclog the hose try hol ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum
In my lg cyking vacuum cleaner, red light appears and the cleaner switches off. Can you please help in what is the problem and in resolution?
... LG Vacuums
I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.
Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums
I just bought a hoover floor mate for hard floors. The problem is the water with cleaner is not coming down to the brissles at all. Help please. It is brand new. any ideas???
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40471&thid=603805\015\012I just bought a Hoover\015\012Posted by serdmann4 on May 17, 2008\015\012I just bought a ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary
This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum
VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter
There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums
My dyson animal works for a while then shuts off...i guess it's getting hot and automatically turning off to keep damage from occuring. i have cleaned the filter and all the collection basket, but am still ahving problems. it was just services a year ago and a new switch installed. please help!!!
The belt that drives the beater bar may be broken or stretched, causing the motor to turn more freely, therefore causing the motor to rev beyond it's design.Jim ... Vacuums
Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.
... Euro-Pro S3325 Handheld Steam Vacuum