Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.
Check the belt and what got stuck in it
I had the same thing happen and when I removed the bottom plate on the bottom (there are three plastic screws to turn and the plate slips off) I found that when I got the thing caught and pulled it out it broke the belt and that was why the beater bar brushes didn't turn.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.
Check the belt and what got stuck in it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My Hoover Deluxe Rewind Elite will not pick up anything. My daughter got something caught in it last night and it made that noise when you get something hung. We turned it off but today it will not work. Is there a reset button?
When you are saying "today it will not work" do you mean the motor runs, but the unit will not vacuum, or are you saying nothing happens when you try to turn it on?If the motor run's, the belt probably broke. You will need to remove the b ... Vacuums
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
Won't work My Eureka Mighty Mite 3670 Bagged, was working fine, and we unplugged it to switch to another outlet in another room and it just stopped. We tried several other outlets and it just won't turn on. We thought maybe it got hot because we had been using it for a while and we let it rest for a while and then changed the bag just to be sure, although it was not full. But it still will not turn on. Any ideas?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=12151&thid=646957\015\012Won't work (by 2 users)\015\012Posted by AndiR on Jun 04, 2008\015\012My Eureka Mighty M ... Eureka Mighty Mite 3670 Bagged Canister Vacuum
I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.
My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.
If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha
... Eureka Smartvac 4870 Bagged Upright Vacuum
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
I was vacuuming over some fringe and then the brush just stopped working and there is nothing caught in it. It spins freely when twisted by hand, but will not turn when vacuum turned on.
Have you checked the belt? it could have snapped when you caught the fringe. also if it has a separate brushroll motor there should be a reset that probably tripped out. ... Vacuums
I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.
... Hoover F5826-900 SteamVac Upright Wet Washer
Wertheim XL180 vacuum cleaner not working The past month our XL180 would stop working after 20-40mins therefore we'd wait 1-2 hours to resume cleaning. Now it doesn't turn on at all. Would this mean its good for nothing? Tips on maintenance would be much appreciated, i consider myself a handyman always willing to give something a go.
Thanks for using FixYa and welcome to the site. Sorry you had to wait to long. First, try checking the cord. Try moving the cord in certain areas to see if the cord has a break in current. If it does, it will need replaced. You have prob ... Vacuums
The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?
This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum
I by accident sucked up the corner of a sheet into the powermate of my vacuum. I turned the vacuum off and pulled out the sheet but now the powermate is no longer working (suction works fine) Is this something I can fix on my own?
These power heads have a kill switch on them. Not exactly clearly labeled. the kill switch reset button should be on the right side of the unit as you look down like you are using it. you may want to try pushing it with the power to the p ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My iRobot Roomba 560 starts spinning sporadically during the cleaning, and after over 3 minutes it complete stops and beeps 9 times. It is necessary to turn it on until it decides to work properly, and keep waiting for the next time the same failure will occur. I tried to reset it, and I have all the dust removed including from the bumper and sensors.
It's the bumper. Blow it out with compressed air and clean the cliff sensors. If you still get the 9-beep error, call support. ... iRobot Roomba 560 Robotic Vacuum
My kenmore progressive true hepa that I just bought--the electric carpet attachment stopped working. Is there something I need to do? It appears to be plugged in properly.
Hi,These are the only possibilities that could make your kenmore not working.1)Check the cord bad at male prongs.2)Tripped circuitbreaker.3)Blown fuse.4)Loose hose electrical connectio ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?
If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum
When I engage the beater roller it will work for a short time (15-20 seconds) and then squeel loudly as if something is not engaging properly. I checked the roller ends and cleaned them but it seems to roll freely by hand while connected to the belt and then at a time it becomes very hard to turn by hand.
Sounds to me that the motor is shot. There is a main bearing the belt shaft connects to and it sounds like the bearing is seazing and gets worse when it nheats up. Soon it wont turn anymore at all ,once it siezes completely. These are rarely worth f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...
The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Help Hi I have had my irobot roomba model 4000 now for 3 months now, I just LOVE it sooo much. I have used it everyday since I got it. But now it is not working. I cleaned it all out I even sprayed it with that air spray can. What happens is, It starts to go then it acts like there is something in the way and stops then goes the other way, then goes off. What is wrong? Please help!!!
I had the same kind of problem with my model 400 today...after starting it and having it go in a circle for 30 seconds or so it would finally run into something and then back up a few inches, turn, then go forward a few inches, then back up a few inc ... iRobot Roomba 4210 Bagless Robotic Vacuum
My Dyson just stopped sucking up dirt. I have checked all the obvious things like clogs and filters. I noticed when I turn it on, there is a valve on the top of the cannister that opens and you can feel suction from the vent hole. Is this valve malfunctioning, or is it working correctly because something else is malfunctioning?
Your cyclones could be clogged. You can clean them yourself pretty easily. See this video. http://www.youtube.com/watch?v=2OO3ugkyzxk ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?
After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
I have a Dirt Devil Vacuum that won't start up anymore. It was working, but then it stopped. The tube got clogged up. Now the tube is unclogged and empty and it won't turn back on. It's also hot on the bottom of it. Help? Blown fuse or what?
Some of the Dirt Devils have a reset button on the back, near the bottom. But if the it is getting hot on the bottom, that may mean the motor is trying to run but can't. Maybe something has jammed it. You would have to disasemble it to find out. ... Vacuums