Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
My Dyson D17 won't work while upright.
\015 I had a clog, and i cleaned it, retook apart the whole vacuum, and made sure again nothing was clogged. it still won't work in the upright position. I can't seem to tell if it's even getting suction when not in the upright position.\015
Check and make sure you have the gasket installed correctly that goes on the center of the cyclone and seals against the canister trap door. If this is backwards, you can lose a lot of suction and it will plug your permanent filter quickly.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.
It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My Dyson D17 won't work while upright.
Check and make sure you have the gasket installed correctly that goes on the center of the cyclone and seals against the canister trap door. If this is backwards, you can lose a lot of suction and it will plug your permanent filter quickly. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The extendable wand wont work? - Dyson DC25 All Floors Bagless Upright Vacuum
Throw you dyson away and write nasty messages here because dyson has the worst website for information. for what we pay you should get on-star ... Dyson DC25 All Floors Bagless Upright Vacuum
My dyson dc07 wont work using the hose i have
Theres a o ring when u tilt the dyson from upright to 45 degree you will see it its either come off or the plastic housing that it sits in is not inline ..mark ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.
Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?
Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson wont staND UPRIGHT
Hi its Darran at Dyson. So that we can help resolve this, please call our Helpline on 0800 298 0298. One of our advisors can through some simple checks with you which will hopefully resolve the problem. We look forward to hea ... Dyson DC25 All Floors Bagless Upright Vacuum
My dyson vaccumm wont stay on it works but i have
Is it a switch or a push button? ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Our upright Dyson has just stopped working. No
There are four possibilities: \015\012\015\0121) If in a country that has a fused plug, the fuse in the plug (unlikely). \015\0122) The switch (unlikely). \015\0123) A break inside the cable that you cannot see (quite likely). \015\0123) The mo ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My dyson dco4 wont pick up when upright
Check the internal pipe underneath is not split ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The brush wont turn on my dyson DC 14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Sounds\015\012 as if you need to replace the brush belt.JimLet me know if this helps. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My dyson works with the hose but wont work the normal way
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson dc15 bagless upright. my brush bar is not working but if you use the hose it works .
\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf\015\012\015\012Check the above link to see if it h ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
My Dyson DC17 Animal Bagless Upright does not click to stay in an upright position. It works but the handle falls to the floor.
This is a common fault with the Dyson DC07 (and other Dysons) unfortunately the clip that holds the handle upright hs broken. It can be repaired, but will cost a reasonable amount to have done... I would just live with the problem and prop the vacuum ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
My dyson dc14 wont turn on at all - Dyson DC14 All Floors Upright Vacuum Cleaner
Hi I would suggest you first check the Fuse in the plug. This is quite common. \012\012If after chnaging the fuse the machine still doesnt work then please come back to us. Let us know that you have checked the fuse andthe machine still w ... Dyson DC14 All Floors Upright Vacuum Cleaner
Dyson wont turn on and its a bit smelly - Dyson DC07 Bagless Upright Cyclonic Vacuum
It sounds like the motor has overheated and has now been irrepairable damaged. The motor has a built in over-current trip to protect itself (and you if it seriously overheated and caught fire). This normally automatically resets itself, however ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I Have a hoover purepower 1800w upright vacuum cleaner that works perfectly except for it wont stand upright anymore. Any advice
Not sure what model of Hoover you have, you may need a new handle release. ... Vacuums
Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My dyson exrenable tube wont lock in - Dyson Ball DC24 Bagless Upright Vacuum
Hi there, its Darran at Dyson.Sorry to hear of the problem that you are experiencing with your Dyson vacuum cleaner. If you are having trouble locating the wand handle back inside the hose, it could be that the hose itself is ... Dyson Ball DC24 Bagless Upright Vacuum
Need diagram for d17 dyson - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Here is the manual:\015\012\015\012Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.
Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum
Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?
Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum
DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum
Dyson ball DC24 brushes wont go round - Dyson Ball DC24 Bagless Upright Vacuum
... Dyson Ball DC24 Bagless Upright Vacuum