Having problems with your Dyson DC25 Vacuum ?
There is a blockage in the wand itself.
\015 Something managed to make its way into the wand itself. Is there any way to remove the wand from the handle to try to clear it?\015
Take the dirt bin off and press the clip at bottom
Repair Help & Product Troubleshooting for Dyson DC25 Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The wand appears blocked but there are no blockages, there is enough suction to collapse the wand but no suction
The filter at the bottom has been washed or not? ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.
Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums
My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
There is no suction from the sweeper head but plenty from the wand. I have viewed several videos and visited seveal dyson web pages and none address this problem. I have thoroughly checked for blockage per video instructions. There were NO BLOCKAGES. Please help. Thanks Doug
Hi Doug,\015\012\015\012There are several things that this could be. Probably the most common problem that we see when customers come in with this problem is actually a fairly simple problem to fix. Here are just a few things that this co ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
There is a blockage in the wand itself.
Take the dirt bin off and press the clip at bottom ... Dyson DC25 Vacuum
The wand on my DC07 Vacuum has no suction. I have taken aprat and can not find a blockage
... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.
You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
No suction when wand is used. Checked for all blockage. If you disconnect no suction at base
Hi there,Sorry to hear you're having difficulties with your DC24. Although I note you've already checked for blockages, you may wish to follow the steps shown in our support guide, to make sure you haven't missed anything: ... Dyson Ball DC24 Bagless Upright Vacuum
I have a blockage in the wand and don't know how to remove it. No suction
Disassemble Your Dyson Animal so you can access the area around the wand. If the block is in the wand itself, you can clear it by passing something through it (such as a broom or mop handle).\012\012Blocks in other piping and outlets can be r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.
... LG Vacuums
Blockage in pipe of my dyson slim dc18
There sould be a rubber flap under the pipe.Pull it down to remove dust and **** that gets stuck. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
No suction on wand of Dyson DC14 Animal
Hi its Darran at Dyson.It sounds as though the wand handle is blocked. To check this, remove the wand/hose from the machine as if you were going to use it to vacuum the stairs. Switch the machine on and test the suction at the top of the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have Dyson animla and the wand stop working....no bloc anywhere
The hose is getting twisted on the machine and that makes it difficult to pull it out.\015\0121) Pull the wand out as far as you can - if you can pull it out completely, separate it from the hose and apply baby powder to the metal rod. Stretch ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson DC07 bagless - upright mode v poor suction, wand mode ok
I suffered with a serviced but not sucking DC07, its fixed now. How? By replacing the cyclone unit via anotherbay, it was an accumulation of dust and debris in the section that is not accessible. Borrow a working cyclone if you can and check the diff ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a Infinity Vacuum Cleaner. Shark Model NV32. I took the wand out to vacuum a spot and now I can't put wand back in. I keep pressing the wand release button when putting the wand in but no good
My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.
... Kenmore 25512/ 25513 Progressive Canister Vacuum
Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!
... Dyson DC05 Bagless Canister Cyclonic Vacuum
I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C
... Filter Queen Majestic Canister Vacuum
When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?
There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.
Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums
No suction no blockages was working fine
Hi there, I'm sorry to hear you've had difficulty with your DC18. If your machine isn't picking up as well as it should be, there may be a blockage in the machine. If you haven't been able to locate one in the cleaner head or internal hose, I ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
No suction out of the wand part
Hi Freda,I'm sorry to hear you're having difficulty with your DC07. Although I note you've already checked for blockages, I'd encourage you to follow the simple steps shown in our online Support guide, just in case there's anything you've mis ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How do you remove the hose to ck for blockage?
If the hose collapses and there is no suction, that is a sure sign of a clog. The clog will be on the opposite side of the collapsing hose from the motor. Good luck. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Suction in Wand Only, (No suction down below).
Check the small hose that is under the machine ( it connects to where the brush roller is ) also you can remove a u shaped tube near the bottom of the machine and also another on the right side of the machine near the bottom as well ... Dyson DC07 Bagless Upright Cyclonic Vacuum