Having problems with your Dyson Vacuums ?
Dyson dc04 cylinder loose when i lift it up??
\015 When i lift the dyson dc04 up .the cylinder comes loose abit ??..any help ..please..??\015
Repair Help & Product Troubleshooting for Dyson Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Dyson dc04 cylinder loose when i lift it up??
... Dyson Vacuums
Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?
You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Loose wire - Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
If the loose wires, you must proceed to TIGHT very well or resolder the wires.if you need to buy wires go www.dyson.com and proceed according.God bless you ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Dyson dc04 Loose wire
Retigh the loose wires, with screwdriver or resolder the loose wires.if you nee buy something go to www.dyson.com and look for order.God bless you ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is.
If it is at the on/off switch, you can carefully prise the yellow button out to reveal a torx headed screw. Remove the screw then the housing for the switch can be pulled out which should reveal your loose wire.\015\012\015\012Brian ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum
Dyson 04 cylinder loose?? - Vacuums
DYSON DC04 how to remove switch housing to check
Its most likely not the switch, check the power cord.. check where the cord meets to the vacuum. the cord could be going bad and most likely not a loose wire. ... Vacuums
Dyson dc04 instruction manual - Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Hi there,You can download a copy of the DC04 user guide directly from our website:http://media.dyson.com/downloads/uk/floorca ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
How do I open my dyson cylinder - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Hi its Darran at Dyson.If you are referring to the cyclone top and bin assembly, once removed from the machine, there is a button at the base of the handle that has Dyson written on it that you press and pull the cyclone top and bin apart ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?
Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums
Dyson DC04 Clutch removal
Smelly Dyson DC04
Hi Philip,I'm sorry to hear you're having difficulties with your DC04. If the machine's making an unusual smell, we'd advise against running it again. I'd encourage you to get in touch with us directly so we can help resolve this.You ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.
I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Dyson My Dyson DC04 runs for a second or two then stops. I have checked the motor. The brushes are good but the commutator is a slightly pitted.Do I need a new motor?
Hi.\015\012\015\012Check mains lead where it enters machine very common for internal fracture.\015\012\015\012To prove this try waggling lead with machine switched on if it starts & stops this is the fault.\015\012 ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Emptying cylinder Have just acquired Dyson DC07 Bagless Upright Cyclonic Vacuum without instructions. How do I remove the cylinder to empty it?
I hope you've found out by now, but, in case you haven't, the latch to remove the canister is right by the handle on top of it, just don't lift until you release the latch with your thumb, it's got a safety to keep you from hitting the release when y ... Dyson DC07 Bagless Upright Cyclonic Vacuum
No suction on my Dyson canister vacuum. - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Hey,I see this problem is more frequent..I'm guessing your dyson 'sounds' blocked.See my solution:http://www.fixya.com/support/t4547920-loss_suctionThis fixed mine right up.It was not working well at ALL, so i open ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Motor on dc04 zorbster slows down - Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
How do i clean all the dyson dc08 - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Hi its Darran at Dyson.A full blockage procedure can be found in your user guide or on our website at www.dyson.co.uk/support. I hope that you find this useful and should you require any further assistance with your DC08, plea ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Loss of suction in dyson dc08 - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Hi there,If your DC08 doesn't seem to be picking up as well as usual, there may be a blockage in the machine. The filter may also need a wash.The easiest way to locate and remove any blockages is to follow the steps shown in our onlin ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Dyson upright My Dyson cleaner suddenly screemed at me and stopped with a puff of smoke and burning smell. I had just emptied the cylinder. It is five years old.
Hi this is an expensive repair and would probably be cheaper to buy new one the problem you have is with the motor bearings seizing its expensive to repair because when dyson made thes vacs they were made so you need special tool to take them apart s ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Sometime when I am vacuuming carpet or a large area rug, my Dyson starts making this loud, horrible, wrenching noise. It stops when I lift one of the wheels up. What is causing this? I have only used my Dyson 3-4 times.
You will need to have the clutch replaced. this is causing your problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson does not start? - Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Check fuse in plugcheck foot switch clicks when pressedcheck cable for damageif non above replace motor ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
Dyson dc04 serves manual - Dyson DCO7 Upright Vacuum
Hi there,For information on using and maintaining your DC04, please refer to our Support page for this machine - just select the model you own from the list:h ... Dyson DCO7 Upright Vacuum
Dyson brush replacement - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Hi there,I'm not sure which brush you're referring to, but you can order replacement parts and additional accessories for your DC08 directly from our online store: ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Dyson DC04 hello, my dyson seems to run ok in upright but when i tilt back the motor sounds like it is struggling, do you think it's down to the rollers being to low and can you adjust height of rollers to overcome said problem? yours chris
Hi.\015\012\015\012If the motor is struggling check to see how easy it is to rotate brush by hand it is stiff to rotate the bearings in the roller may be siezed or the roller could be clogged with hair etc check it & let me know what ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum