Having problems with your Electrolux EL5020 Vacuum ?
The belts not turning
\015 It was making a loud noise now the belts not turning\015
For sure the fan is broken that was the noise has to be replaced if you didn't feel any burning smell the motor still good also the first thing should be replace the belt for a new one the old one might be worn
Repair Help & Product Troubleshooting for Electrolux EL5020 Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a
Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum
The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th
... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?
Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?
Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]
Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.
Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.
If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?
Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?
... Eureka Smartvac 4870 Bagged Upright Vacuum
Roller not turning, belt not working no water . The belt on my Bissell Proheat is not getting water (although there is plenty in the holding tank). It seems the belt is not turning and there fore the water is prevented from leaving the holding tank.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Model DC14 beater brush doesn't turn. belt from motor turns but doesn't turn beater brush belt from clutch . Is clutch bad??
You might need to replace both belts. You can get them here:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums
7901-1 brush stopped turning belts are O.K. brush can be turned but is too stiff for the belt to make it turn.
You may need to replace the brush unit. Make sure your belt is tight and turns. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?
I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!
... Hoover Vacuums
LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough
The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum
Ratchet noise, beater will not turn, belt not broken, in carpet mode the Dyson d07 makes huge ratchet noise and the belt will not turn the beater brush.
Ok, so I had the same ratching noise and took the advice of many sites directing me to clean the brush. But like most I cleaned the brush and the noise continues and the brush does not spin. Reluctant to take it to get serviced I dug a l ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
The power nozzle works but only on tile. the brush does not turn. the belt is intact. could the motor that turns the belt be broke? is this something i can replace myself or is it better to bring it to be serviced
Depends on you if you feel you could possibly repair it by replacing the electrical motor or you may just have a wire thats nolonger getting continity. enevitably it's your decision if you can repair it you will come off cheaper :) ... Electrolux Guardian Bagged Canister Vacuum