Having problems with your Eureka 2961AVZ Bagless Upright Vacuum ?
How to fix a vacume that is smoking
\015 I was vacuuming a the vacuume started smoking, the belt is good, and i cleaned the brushed started it up again and started smoking still what do i do\015
Any electrical unit that smokes,is ,not worth repairing
Check to see if the bushing on the roller brush has seized up. The plastic housing can get hot and melt. Could be caused by hair and dirt preventing the bushing from turning, or if the brush is jammed out of proper position. If the bushing has melted, the part number for a new roller brush is #EU62228-3.
Repair Help & Product Troubleshooting for Eureka 2961AVZ Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to fix a vacume that is smoking
Any electrical unit that smokes,is ,not worth repairing ... Eureka 2961AVZ Bagless Upright Vacuum
Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor
... Eureka 3041BZ Upright Vacuum
The brush on my Electrolux Ambassador III vacum stops turning after vacuming for only a few minutes every time I use it. The power nozzel is less than a year old and except for the brush not wanting to turn, it operates just fine. Any suggestions on how to fix the problem?
... Electrolux Vacuums
I have a Dyson DC14..I was vacuming and when I stopped the vacum would not stand up..it wouldn't click in the stationary poistion. When I turned it on all the suction is coming from the hose even though it is tilted. Can I do something to fix this?
Yes! Stand behind the machine. Hold the handle at about 45 degree angle. Remove the airway inspection valve (press the yellow release button that's between the right wheel and the clear bin and then just pull away that curved piece of plastic pipe). ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
How do you fix the beater bar in a dyson vacum. Otherwise the vacum works fine.
Its either the belt or the roller switch. Most likely the belt. Go to lowe's and get the replacement belt.Remove the screws that hold the cover on the bottom of the vacuum and remove it. You will see the broken belt. pull it out of the va ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?
Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning. If the vacuum is left on any longer the belt starts smoking. I took the case off and there was a little debris but not much. Is there a cause and fix or just time to replace the belt?
Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum
We bought a new home in march. It is a brand new home, with brand new First Alarm smoke/CO detectors. The very first night, we noticed the iving room (main) smoke alarm was "chirping". So we tried to replace the batteries, but when we did, all of the smoke alarms started going off (they are hardwired). We took out the new battery & dealt with the chirp. It is getting to be too much. So we are trying to fix it, but everytime we replace the batteries, the alarms are silent for a little bit, & then
Vacum overheats and starts smoking after 4 minutes of vacuming
Clean vacuum internally, if the problem persists replace the motor. ... Panasonic MC-V7395 Vacuum
There is a rubber valve on the top of Dyson DC14 all floors. When the vacum is locked in its upright position or the hand wand is used there is a whistling sound coming out of the valve. When the vac is used as a floor vac, it does not make the sound. Is this something that I can fix? Is there an obstruction somewhere that would be causing this sound? thank you.
The Fixya user in this repair is giving out personal contact information rather then helping the customer out on the Fixya board. This defeats the whole purpose of Fixya if the "TheDysonTeam" just gives out his phone number and helps the customer o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I have a Kirby G7 and it will run on the low speed setting. When i switch to the high speed it starts to spark and smoke near the back of the motor near the windings. Do i have a motor going bad or is there a simpler fix.
It's probably doing that on low speed too, you just aren't noticing. What you'll have to do is get to the motor. Look at the armature and see if it's scared, missing an pieces, scratched up.. if so, then your motor is shot, throw it away.. If not, if ... Vacuums
My vacum will not start a red question mark lights up. Can this be fixed?
This light indicates the bag needs changed. If you've done that, The possibilities are a clogged hose, clogged elbow at power nozzle, or on certain models a bad Control Valve Assembly. If yours has a dial on top, turn so the smallest dot lines up w ... Electrolux C101 Bagged Canister Vacuum
The vacum is 7 months old andAll of a sudden is very hard to push and it has lost suction how do I fix this
Sounds like a broken belt. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
Have a dyson vacum and the beater bar stopped working. How do you fix the beater bar.
Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Brush stopped spinning from fabric being sucked into it, how can I fix it? It's a Dyson animal vacum. The belt is not moving from the lower motor.
Turn upsidedown.\015\012There should be 3 plastic screws in a triangle shape.\015\012Loosen, but do not attempt to remove the screws.\015\012This will release a shield that will expose the brushes.\015\012Carefully remove the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My miele s571 hoover is humming from a normal sound to a real low hum sound and their is a smell of burning it even through my smoke alarms off what would be wrong or is it worth fixing
It could just be a slipping belt, hair and lint get under the belt and make it stretch the it slips and the spinning drive post heats it up until it starts burning. ... Miele S318 Bagged Canister Vacuum
My vacum will not pick up dirt and it is smoking a little from the bottom.
Siunds like the beater bar has seized take bottom off and check belt and brush ... Dirt Devil Breeze Bagless VacuumVacuum
The vacume turns off when it is put up strat. But works when it is tilted how do i fix it?
I have had this problem and it is in the actual propelling switch which is a real pain to get to and once there, clean and reassemble ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Beater bar not moving. Is there a belt? My mom sucked up a sock and didn't know. So she kept vacumming and then smelled something rubbery burning. And then we found the sock and cleared it. Then the beater bar wouldn't move after that. How do I fix it.
Hello,The belt is broken or badly stretched and needs to be replaced. Here is a link to download a manual.Look for the "Download Manual" on the right side of page. Scroll down towards bottom of page and you'll see how to open it up to cha ... Eureka 4700A Maxima Bagless Upright Vacuum
My Fantom Vacum Cyclone et was smoking and smelled of rubber burning. I'm sure it is the belt but I don't know how to get into the vacuum to see the belt.
To replace the belt, Remove the covers over the headlights and under the shiny foul. there are two screws. (In other words: Remove the lens covers, bulbs and the foil. under the foil are two screws.) Then, there are two tabs that hold do ... Fantom Vacums Cyclone XT Upright Vacuum
HOOVER VACUUMS MY MOTHER'S WORK, MERRY MAIDS, USES ALL HOOVER VACS. THEY ARE LIGHTWEIGHT-UPRIGHT-BAGGED VACS. I TRY TO FIX THEM WHEN THE MAIDS BREAK THEM; BUT, I'M HAVING PROBLEMS WITH A BURNING SMELL AND ONE MOTOR EVEN SMOKES. I'M NOT SURE THE MODEL. CAN YOU HELP? THANK YOU.....
Go to thehooverstore - this site lists a whole bunch of hoover machines, exploded diagrams and parts lists. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum
WHEN I TURN MY VACUME ON IT SOUNDS FINE, WHEN UPRIGHT. WHEN I GO TO MOVE IT TO HOOVER IT MAKES A SCREAMING NOISE. CAN U TELL ME WHAT IS WRONG PLEASE AND HOW TO FIX. THANK YOU
When the vaccum is upright, the beater bar is not engaged. When you tilt the handle back, the clutch engages and the beater bar begins to turn.\015\012\015\012There are two likely possibilities for the "screaming noise". First, and most l ... Dyson Vacuums
Changed belt in my vacum and it is now smoking and i smell burnt rubber
Hi,\012Check the brush and make sure that it seated correctly...between pulling on the new belt and getting the brush back into the slots sometimes it will bind up...\012You also will now want to put a new belt in now... the belt is toast ... Eureka 4467AV Upright Vacuum
It just stopped working - without any smoke or weird smell. It does not look like motor but I do not know - Is it worth fixing it or buy something new. If I could I would buy the same one but they do not manufacture it anymore
If the motor get over heated it will just switch off on you, let it cool down and try it again later,,,\015\012there is also a thermal fuse inside the motor if this has poped on you then its a bust bin job im sorry to say,, there is realy not a ... Black & Decker HV7010 DirtBuster Handheld Vacuum
Roller does not work. My vacume works fine , but the roller does not work. How can i fix that/
Remove the brush assembly, and clean/oil (3in1 or similar) the end bearings. If the belt is broken/damaged, replace same. Install the belt on the roller and motor shaft, then install the brush into the vacuum base--make sure the belt is half twisted ... Dyson DC07 Bagless Upright Cyclonic Vacuum