Having problems with your Fuller Brush Wet Mop Replacement Head - - ?
How to attach fuller brush wet mop replacement head?
\015 How do I attach it to the pole? Does wing nut go on the front or back?\015
On the back
Repair Help & Product Troubleshooting for Fuller Brush Wet Mop Replacement Head - -
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to attach fuller brush wet mop replacement head?
On the back ... Fuller Brush Wet Mop Replacement Head - -
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
When i attached the mop head and begin to mop, water comes leaking out of the unit. I have tried different mop heads and it is doing the same with all. is this a common problem with the shark? i've owned it less than a year.
\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david
Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums
The extra large mop head attachment will not release steam. It seems to be clogged, and the steam escapes above the head attachment. How can this be resolved?
Hi,I saw this post, so I had to go and checkout my wife's shark....If you pull the attachment off and look inside you will see that there is a small hole that the steam travels through into the flexible hose with the spring around it and ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
My shark steam mop is not working properly cannot find manual what can i do i am in the older generation and not technical mop head is getting too wet or not wet at all. steam not even thanks
Google is your best friend. EVER ! http://www.sharkclean.com/cgi-bin/livew/site.w?loc ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Where would I find a replacement power head with brushes
Try this link belowhttp://www.vacpartswarehouse.com/FANTOM-vacuums-bags-belts-brushes-parts-and-accessories-s/4206.htm ... Fantom Vacums Lighting Canister Vacuum
The mop head has broken on my x5 steam mop can i replace it
My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t
... Hoover Vacuums
How to Replace Rotor Brush for Fuller Brush Electrostatic Sweeper
... Fuller Brush Repl. Brush for Electrostatic Carpet Sweeper - -
Hi there my dyson suffers from a lack of suction with of without the hose attached. we had our local repair man look at it and he replaced a hose in the head of the machine.i have replaced all the filters and ideas?
What about doing this:\015\012\015\012http://www.fixya.com/support/t2936439-dyson_suffers_from_lack_suction ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Suction on my dc08 is very poor when turbine head is attached - no problem when not. I have cleaned the brushes an ensured there are no blockages. Why the loss of suction when using turbine head ?
Please go to the web page www.dyson.com and go next http://www.dyson.com/support/help.asp?article=1468&product=DC22-TURBINEHEAD-USand fix it. with commong sense.God bless you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums
After plugging in the steam mop, waiting for the 30 sec, pumping 12-15 times - no steam comes out. the tank is full and if i take off the bottom attachment the steam sprays everywhere. but the steam will not come out when mop head is on. thanks
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee
Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(
... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz
Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums
Kirby Ultimate G will not suck with main brush head attachment
You need a new belt. When the green light goes out, the brush is not spinning. The belt is stretched and needs replaced. Here are detailed belt changing instructions....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum
I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne
... Hoover S3614 Vacuum
Replacement belt for rolling brush attachment
Shark steam mop head is clogged - No replacements??
Hi, replacements can be found on amazon. Here: Amazon com Euro Pro Shark Steam Mop head . I hope this was helpful. Cheers ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Have an e-series rainbow. Belt and brush bar have been replaced in power head. But the red reset button can still be pushed and it is not staying going like it should. May it be the motor?
... Rainbow E series Canister Wet/Dry Vacuum
I am using a Kirby Hertigae II shampoo attachment and the belt broke, I am trying to replace the belt, but cannot remove the bottom brush that the belt hooks onto.
Try using a pair of pliers on each side to remove the screws you only need to remove 1 ... Kirby Heritage II Vacuum
Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum
I have a Bosch Elector Duo Hepa, BSG71360UC/07. I'm trying to replace the rectangular-shaped part with the carpet brush that attaches to the bottom of the wand. Where can I find this part?
... Bosch BSG71360UC Bagged Canister Vacuum