Having problems with your Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum ?
Cannot find replacement piece for the scrub brushes.
\015 I need to find replacement piece for the scrub brushes. The whole piece with the brushes broke and won't stay on when I'm using the cleaner.\015
The part number for this brush block is 48437022, most repair shops will have or can get it for you.
Repair Help & Product Troubleshooting for Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Cannot find replacement piece for the scrub brushes.
The part number for this brush block is 48437022, most repair shops will have or can get it for you. ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne
... Hoover S3614 Vacuum
I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher
If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums
Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems
Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums
My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou
Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Im trying to replace the belt but cannot find where to connect it
Vacuums are different. Look for a small motor shaft within the belt's reach. ... Vacuums
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david
Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.
Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum
We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?
Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://184.108.40.206/v/u6451900.pdf ... Vacuums
Where would I find a replacement power head with brushes
Try this link belowhttp://www.vacpartswarehouse.com/FANTOM-vacuums-bags-belts-brushes-parts-and-accessories-s/4206.htm ... Fantom Vacums Lighting Canister Vacuum
I need replacement carbon brushes for the motor. I haven't been able to find a source.
Try looking for a power tool repair shop, they usually have some brushes and can order more. I have put Hoover brushes in my Shop-Vac.\015\012 Look for some that are close to matching,( spring size,spring length, brush length). If the brushe ... Hoover Portapower C2094 Bagged Canister Vacuum
Nilfisk GD930 vacuum-can't find replacement brush
Hello mddamus,\015\012Try this link to a Nilfisk supplier, speak with a rep and they should be able to identify exactly what you need and provide that part for you.. ... Nilfisk GD 930 Canister Vacuum
My Delonghi DSS50 steam floor cleaner water reservoir has a broken valve on the bottom where it fits into the steam unit. It leaks water rather than producing steam. I would like to find the valve and replace it or buy a new water reservoir with the valve in it. I cannot find the part I need. Can you help me?
... DeLonghi DSS50 Scopa Upright Steam Vacuum
My B50 Keurig single cup Brewer works great but this am, I find that the bottom Sharp Needle is gone and I cannot find it. It is the needle that punctures the bottom of the K-Cup. Needle and little rubber piece is gone - DO YOU SELL THIS.
Herein Fixya we don't sell anything, we just give some guidance how to find thepart you need. Also Keurig makes it next to impossible to get parts unless youhave sent in your warranty and even then they want you to send the ... Vacuums
Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
The spinning brush on the side kept falling off. I would put it back on as the little screw usually remained with the brush. Last time it fell off (it has every time I've used it) I lost the tiny little screw. I cannot find reference in the manual to its specifications. As I have had it for less than a week, I am considering returning it.
Its so annoying to find Roomba after he's finished cleanin only to see that once again he's lost his brush. How to keep your Roomba from losing his brush- items needed: quick steel putty (local hardware store), crazy glue, original screw (or similar ... iRobot Roomba 530 Robotic Vacuum
Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?
Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum
I am trying to find the powermate parts to replace the roller brush on this vac I have trouble finding websites that sell these. I need to know the item numbers so that I can order the correct items to fit this model.
Brought the powermate part to local Sears part store and they ordered the items we needed \015\012 thanks for trying to help \015\012\015\012GFreckles913/Glenna Rodell ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Suction Hose The suction hose has cracked so the suction feature no longer works. I would like to replace it, but cannot find that it is a replaceable part. Hopefully someone else has a solution.
Go to0 http://www.thehooverstore.com/h3000.html there also is a parts break down. You can email them at ... Hoover Floormate H3000 Upright Wet/Dry Vacuum