Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?
How to unclog i guess
\015 It spit the water out but don't **** it back up\015
If this has a foam filter on the bottom side of the recovery tank lid, make sure there is at least a 1/4 in. gap from the top. Also check the filter from the bottom, it has a red frame, clean it off it covered over. The other thing that will cause this is that the lid for the recovery tank is not locked down all of the way around.
Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to unclog i guess
If this has a foam filter on the bottom side of the recovery tank lid, make sure there is at least a 1/4 in. gap from the top. Also check the filter from the bottom, it has a red frame, clean it off it covered over. The other thing that will cause ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
How do I unclog a bissell vaccum? I'm not just talking about unclogging the hose, I need to unclog the complete vacuum cleaner. HELP!!!
Well firstly, whats the model number and do you have the user manual to hand? If the main hose has been unblocked, then it could be the main dirt channel which is blocked just after the moving roller brush panel. A long pipe cleaner or wi ... Vacuums
Its for a central vac system. I have very low suction power. I've emptied the dirt trap. It seems the fan is working ok, so I guess theres a clog somewhere but I have no idea how to find and fix it. I have no manual on the unit as it was in the house when we bought it. I'd guess its same age as house (19 years old). Any advice would be graetly appreciated!
Usually, low suction would indicate access ports allowing air to enter the system. Easy to test system however. Test vacuum first. Remove intake hose to vacuum ( at the vacuum canister ) and place your hand over intake. You should feel considerab ... Vacuums
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?
Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Unclogging drains? I've recently read (I believe it was on your Ebay site) that they can unclog drains. Can you please briefly give me the basic steps when doing this? What attachment(s) are used? How is the vacuum configured? ***Also - My Kirby is actually (according to the front label on the arm) a "Kirby G 2000 Limited Edition" Thank you!
Hi!You need to take the power nozzle off and attach the thing that looks like a little plastic cup with two hooks on it. This is the intake guard. Attach it to the front. Now remove the cloth bag and put the hose on the hole where the bag was. ... Kirby G5 Bagged Upright Vacuum
Beater bar is seized up. How to unclog bearings?
Spray it with WD40 ... Kenmore 25512/ 25513 Progressive Canister Vacuum
Unclog simplicity fan motor
... Simplicity Vacuums
The solution has stopped going out the hose. The hose seems to be deep inside the machine. How do I get to it to unclog it?
The hose unhooks by the motor. But it could be the valve in the hose head. Maybe this picture will help:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
My dirty devil dual was clogged and after i unclogged it it worked but then it turned off and does not want to turn back on, what could be the problem?
... Dirt Devil Reaction Twin Cyclone Upright Vacuum
Hoover Telios TC3202 200W Cord Rewind is jammed - cannot see how to open body of vacuum to look at the source of the problem. Found 4 screws but that did not help - guess you have to prise something open but cannot see where or how.
There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about the others. \015\012Anyway, this is it. The cover is held to the b ... Vacuums
I have a Kenmore Destiny Plus vacuum, and it doesn't have suction anymore. I've come to the conclusion that the tubes, I guess you can call them that, are plugged. I'm trying to find the user manual/service manual to know how to open the vacuum up to unplug the tubing.
It's October now so this is probably too late to be useful for you but it might help someone: I had the same problem. I used a bright light to see that there was a clog up high in one of the plastic tubes on the side. Using an untwisted wire coat han ... Kenmore Vacuums
U-Shaped piece I was in the hospital for a couple of nights and my 80 year old mother decided to go to my house and vacuum my house. When I went to get it out to vacuum the other night the u shaped part fell off. I guess my mom had somehow knocked it off. Now I cannot figure out where it goes. It is a plastic U-shaped piece. Can you help me? I sat for a hour trying to figure out where it goes.
It attaches at the bottom of the hose and goes into the bottom of the valve. Located on the back bottom of the unit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Hello yes was i was wondering if you could possibley instruct me as to how the inner tubing hoses go back on the 8910 series it appears i am having no luck as to what tube hooks to what port ect? i figured somewhere surley there had to be a service diagram but guess what no luck?
Maybe this picture will help:\015\012 ... Bissell 8910 ProHeat Clear View Upright Vacuum
I think its a hoover any way,i guess at one time some one vacumed up some moisture i can se it on the bottom of motor,on one of thewires theresa thermol senser and i see rust in the plastic,cause it good and thencuts out i think the senser out because of the rust in it???????
If mositure got on it, it could have damaged it and hopefully the motor didn't receive any moisture on the inside of it. ... Vacuums
Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks
Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Clogged my vacum is clogged and I have tried to unclog it but can't find all of the trap doors. Is there a brochure that would step me through it?
You can call your manufacturer of the vaccuum cleaner and get some help. \015\012 Or try unplugging it and turn it upside down and beging taking it apart. Take the brush out and then work your way to the motor. There maybe something lodged up in by t ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum
I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f
I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums
Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.
If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum
Bissel pro heat turbo. I beleive it is clogged with ahir and fiber. i don't see water going up through the front How do I unclog
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums
Rainbow SE I turned the vacuum on and it worked to do one room Then I shut it off to wait until my husband got of his call. I realized that their was cloggage in the vacuum part that vacuums the carpet and unclogged it. I then tried to turn on and it was dead. I have the water filled just above the stick.
The clog may have over heated the motor, usually if you unplug it then after little while, try it again. If it still won't go, does the separator turn easily or is it bound up and won't turn. Take it off and see if the motor will run(without water) ... Rainbow E series Canister Wet/Dry Vacuum
Don't have a manual for my kirby - trying to turn on the blower to unclog a drain but can't figure out how
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566440\015\012Generic problem for all Vacuums\015\012Don't have a manual for\015\012Posted by ssinghnyc ... Vacuums
Shampooer dispensing my dirtdevil shampooer does not dispense water throughtout all holes in bottom. how do I unclog them?
I occasionally run some water and vinegar (equal parts) through the machine, just as I do for clogged holes in my steam iron. So far it has been doing the job. ... Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
Hello, I have a Dyson DC17 that is not working properly. I emptied out the canister to find the tiny holes clogged on the cyclone part of the vacuum. How can I unclog those holes? Thanks!
I had this problem. Part of the clyclone is hard plastic and part is softer - where the holes are. Basically, I removed the rubber gasket at the bottom and kept beating on it - thumpig the hard plastic on a hard surface and then banging the softer ... Vacuums
Help unclog vacuum cleaner
... Fantom Vacums FM741 Twister Bagless Upright Vacuum