Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?
Brushes will not turn
\015 Brushes will not tur. Unit is cleaned. Powers up, etc. but brushes will not turn even though the green knob for the brushes is in the ON position.\015
Look for something wedged between the belt and the turning components. The smallest thing can cause a lock down. Make sure hair is not wrapped around rollers causing it to tighten up at bearing sufaces.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th
... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.
Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.
Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.
... Dyson Vacuums
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net
What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula
There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you
Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums
Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum
The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Brush will not turn on on my Bissell Healthy home vacuum, the brush button is depressed and brush is clear. The vacuum motor works fine, just the brush will not turn on. Is there a part to replace?
... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.
The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]
Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
No suction When I turn the vac on it sounds ok but there is no suction and the brushes don't turn. Alot of air does come out of the two exhaust vents and the brushes will turn manually.
Hey, how are you ?\015\012\015\012here are a ew things that could be causing you sorrow\015\012\015\0121.) Check your vacume to ensure that it isnt clogged anywhere\015\012\015\0122.) before your compressor and aft ... Hoover F6020-900 SteamVac Upright Vacuum
Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine
... Bissell 8910 ProHeat Clear View Upright Vacuum
7901-1 brush stopped turning belts are O.K. brush can be turned but is too stiff for the belt to make it turn.
You may need to replace the brush unit. Make sure your belt is tight and turns. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.