Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?
Carpet Height Adjusment
\015 Sliding the height adjustment knob does not adjust the wheel height. From the underside, the tab, connected to the adjustable wheel plate, does not come in contact with the bottom of the sliding height adjuster. \015\012\015\012Help!\015
In addition to the tab that contacts the bottom of the slider, there are 2 protusions on the adjustable wheel plate that move through holes in the housing, but only when the handle is tilted to begin vacuuming. The wheel plate has a spring that forces the tab against the slider. As the handle is moved to the upright position, the protusions move back through the holes, taking the tab away from the slider and the wheel plate locks in its highest position. Therefore, the position of the slider has no effect while the handle is upright and locked. Hope this helps.
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Carpet Height Adjusment
In addition to the tab that contacts the bottom of the slider, there are 2 protusions on the adjustable wheel plate that move through holes in the housing, but only when the handle is tilted to begin vacuuming. The wheel plate has a spring that ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?
This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum
Can I fix height adjusment?
All i no is on the bottom of unit there is 2 smaller wheels that control the height adj. see if that the prob. ... Hoover U6434-900 Bagged Upright Vacuum
I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?
The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums
Height adjustment The height adjustment button on my upright is nonfunctional. The Height is set closest to the floor and it makes it difficult to move on medium height carpet.
You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum
Carpet Height Adjust Broken - Spring fell out
... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
Carpet height adjustment not changing the height of the brush.
... Eureka Smartvac 4870 Bagged Upright Vacuum
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks
HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I just installed new carpeting and the vacuum makes deep tracks ( 4 of them, corresponding to the grates on the underside). They are so deep, I am concerned it will score or even cut the carpet. There is no height adjustment so I cannot raise it. Thank you
Hi there,The tracklines left by your Dyson are caused by the revolving brushbar grooming deep into the carpet pile to dislodge trodden in dirt, grit and animal hair. However, you may want to contact your carpet manufacturer to ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?
Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Why won't the brushes turn when on the carpet? They will turn if I lift it up off carpet. I have adjusted the height and everything and they won't turn.
Your belt is stretched and therefore won't spin when its against the resistance of the carpet. You just need to replace it. You can get this belt here: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
I have the Dyson DC14 and its like it's not brushing the carpet anymore, The brush is spinning, but its like it isn't self adjusting to the carpet height? It still has suction, but doesn't make the same sound it used to when you'd start vacuuming. Its like it never adjusts anymore???
Hi its Darran at Dyson.It sounds as though the internal hose underneath the machine has twisted slightly. With the machine switched off, lay it on its side and look at the base. You should be able to see a small corrigated hose. Simply t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I bought the 085845 yesterday, put it together and had trouble pushing it on my 8 x10 area carpet. The vacuum did not move easily and seemed to "pick up" the carpet. It seemed that the automatice height adjustment may not have been working. Any suggestions?
I called Dirt Devil and they said return it! ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
Carpet height adjuster
... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum
Cant raise for carpet height
... Hoover Tempo Widepath Upright Vacuum - Blue
How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works
... Hoover Vacuums
Carpet height selector not working on Eureka The Boss SmartVac
... Eureka Smartvac 4870 Bagged Upright Vacuum
Carpet height selector doesn't work.
You have a bad belt. It may not be broke but it's so loose that it isn't turning the brush roller when a little resistance is applied to it. That belt is cheap and it's routine maintenance to change it about every 6 months. ... Vacuums
The carpet height adjustment feature on my boss smartvac does not work
What doesn't it do ? ... Eureka Vacuums
Dirt devil breeze with automatic height adjustment has become hard to push on carpet. How do I fix that?
... Dirt Devil M082550 Breeze Bagless Canister Vacuum
On a plush carpet, the machine is not picking up correctly on any height setting. The agitator is sporadic in spinning. The agitator belt is brand new.
Replace the rubber belt that should fix it if not let me know ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Vacuum height won't go on low carpet setting. Dial will go on medium and high, but not low.
Make sure you're not trying to adjust w/ handle in upright locked position because thewre is a cam which raises the vacuum head a little bit when handle is locked in upright position. If this is not the problem, turn vacuum upside down with handle in ... Hoover Vacuums