Having problems with your Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ?
Windtunnel U6425-900 It seems the vacuum gets stuck in the carpet when the front dips and sucks up the carpet.
I think I may have the solution to all these same problems: If you buy a new front brush this might solve your problems, because the brushes have worn down and causing the vacuum to **** stronger because it is closer to the carpet. I hacve the same problem and I am going to see how much it would cost to buy a brush roller. If it works I'll let ya all know.
Have you tried raising the 'carpet level' adjustment?
Repair Help & Product Troubleshooting for Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Windtunnel U6425-900 It seems the vacuum gets stuck in the carpet when the front dips and sucks up the carpet.
I think I may have the solution to all these same problems: If you buy a new front brush this might solve your problems, because the brushes have worn down and causing the vacuum to **** stronger because it is closer to the carpet. I hacve the same ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I
Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum
I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I'm not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?
That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?
The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th
Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.
May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you
Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums
The vacuum does not **** in dirt. It is blowing air instead. Yet when I disconnect the vacuum from the cannister, the suction seems very strong. I took it to a vacuum repairman, and he said that Kenmore sucks and I might as well get rid of it. (He wanted to sell me another one) It is 10 years old, but if I can fix it I would like to try.
... Kenmore 22613 Bagged Canister Vacuum
I have a Eureka "The Boss" vacuum that doesnt seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.
I have a Eureka "The Boss" vacuum that doesn’t seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.\015\012 \015\012I woul ... Vacuums
The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?
Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?
If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum
LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.
Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!
... Kenmore Vacuums
How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]
... Miele Vacuums
My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?
... Kirby Heritage II Vacuum
I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?
Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?
As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Eureka the boss upright bagless vacuum. how do i open it to get to the belt area? the brush seems stuck. it wont move
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=801547\015\012Generic problem for all Vacuums\015\012Eureka the boss upright bagless\015\012 ... Vacuums
Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.
Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums
Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.
TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum
My Steam Vac does not pick up the water from the carpet why? When I pull the Vac backwards to **** up the water it sucks it up sometimes and sometimes it doesn't Is there a manual I can get I seem to have misplaced mine.
Ebay,google,or the manufacturers website they usually have downloadable manuals... ... Hoover F5858-920 SteamVac Wet/Dry Vacuum
No suction My vacuum does not seem to have much suction when in use. The agitator brush is rotating but I'm not able to get much off the carpet. The suction is fine when I use the attached wand.
If the belt is stretched, then it can't turn the brush rol under load, if you haven't chenged it in the last 6 months, then I would put a new one one. Also check the dirt inlet by the brush roll for a blockage. ... Riccar 8955 Upright Vacuum
Carpet shampooer Why cant i shampoo with my Kirby. I get lots of water over the floor but it doesn't seem to suck it up. Any help would be gratefully received . Thanks.
Hello!\015\012\015\012It sound to me like your shampooer is missing the little round suds screen that goes over the hole where the hose plugs in to the tank. Look inside the hose and see if it's in there. Sometimes it gets turned sideways a ... Kirby Heritage II Vacuum