Having problems with your Hoover Vacuums ?
Belt will not spin - Hoover Vacuums
3 things may be wrong. 1 - brush motor burned up or disconnected. 2 - belt damaged, stretched or missing cogs on belt. 3 - belt is turning but brush roller is not turning due to bearings froze. In all 3 of these cases, the vacuum should be taken in to a repair shop.
Repair Help & Product Troubleshooting for Hoover Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
Hoover spin scrub f5915900 belt replacement - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
On my Hoover Savvy U8174-900 on carpet setting, the brush spins when I pull the vacuum towards me, but stops when I push it forward. Belt is tight and fine.
Hoover savvys have two very common problems that cause this. The first and most obvious is the belt that you checked already. Many times the belt is tight but those particular belts have teeth and should you lose any teeth on the brushroller OR th ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum
Belt will not spin - Hoover Vacuums
3 things may be wrong. 1 - brush motor burned up or disconnected. 2 - belt damaged, stretched or missing cogs on belt. 3 - belt is turning but brush roller is not turning due to bearings froze. In all 3 of these cases, the vacuum should be taken in t ... Hoover Vacuums
I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.
You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?
My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.
Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum
Hoover U5780 Brush Won't Spin (Have New Belts)
... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?
Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?
... Dirt Devil M084600 Dynamite Bagless Upright Vacuum
Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.
You need a new belt. ... Vacuums
On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?
Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum
... Hoover U6441-940 WindTunnel Bagged Upright Vacuum
No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?
Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My hoover savvy vacuum cleaner brush will not turn but the belt is fine. i was vacuuming and smelled a burned odor and thought the belt, but not. what's wrong
It could be the motor on it`s way out ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Bissell powerforce vacuum brisals will not spin and i replaced the belt and it is still not wanting to spin and I think it will pop the new belt. what is wrong with it?
... Bissell 6594 PowerForce Bagless Upright Vacuum
How to change belt on hoover savvy vacuum - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
How do I change the smaller brush belt on a Hoover Windtunnel Cyclonic? ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Change belt on hoover vacuum u4270-930 - Hoover U4270-930 Vacuum
... Hoover U4270-930 Vacuum
Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to
... Hoover U5344-900 WidePath Vacuum
Change belt hoover upright vacuum - Hoover Vacuums
Take out the screws on bottom where the brush is pull out brush assembly and look for a broken belt ... Hoover Vacuums
I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?
Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum