Having problems with your Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum ?
I have a Sears canister vacume mdl 116.2481290 and I need to replace the wheels. I can't see how to remove the current wheels/assembly. Can you help?
Repair Help & Product Troubleshooting for Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Sears canister vacume mdl 116.2481290 and I need to replace the wheels. I can't see how to remove the current wheels/assembly. Can you help? B
... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating
I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed
... VAX Appliances Vax X3 Bagless Upright Vacuum
Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?
Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums
I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.
Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums
I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t
... Dyson DC25 Vacuum
I HAVE TURNED THE VACUME UPSIDE DOWN TO CHANGE THE BELT AND A SILVER CLIP HAS COME OUT, I CANT SEE WHERE IT GOES AND I CANT DOWNLOAD THE MANUAL
Probably an edging clip ... Vacuums
Hoover Alyx Pets 2000w Hoover Model TC1208 001 Virtually no suction, have checked for blockages but cant seem to see any, however i can't remove the hose to check it. Any ideas?
Did you check the HEPA filter? I have the same problem with mine if I don't clean the filter after using it. It's a dirty job but helps for a while. ... Vacuums
I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help
Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums
Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?
You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum
The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.
\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums
I just bought a Tfal Ultimate Autoclean iron FV 9450. I am reading through the manual and trying to figure out all the parts and functions. I cannot figure out how to remove the anti calc valve. I see it is part # 12 on the drawing but that piece on my iron (the bit with the little circles on it where it says, " anti calc plus') seems to be a flat piece of integrated plastic with no give or slide to it. .I cannot see how I'd possibly remove it. What do you do - push up? push down? The i
Anti-calc valve wings (grip) located at #3 of the 1-15 labeled description diagram that is part of the instruction manual. The wings are on either side of the dry/steam control #4. Lift up on the wings (grips) and the dry/steam control will accompan ... Vacuums
My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.
Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it
Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum
Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.
If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum
How to replace wheel bracket on dirt devil. I have a dirt devil swivel glide and I took off the wheel bracket to clean out a clog and now I cant seem to get the wheel bracket back on.
... Dirt Devil SwivelGlide Bagged Upright Vacuum
I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.
Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.
... Bissell 1699N ProHeat Clear View Force Upright Vacuum
How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.
... RTO Vacuums
I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?
Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums
Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.
I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums
My dyson animal vacum hose no longer wants to **** up anything i have removed the botttom part that u can unscrew and removed somethings that were stuck in there since then it no longer picks up anything any suggestions
Check all connections and motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
How can I remove the pet hair that is trapped in the initial vacuum assembly? I don't see screws for removing the clear plastic panel
Generic comment.\015\012\015\012If the parts aren't glued in, they must be snapped in or fastened with screws. You say there are no screws - try unsnapping.\015\012\015\012I think id try a coat hanger first with the help of a ... Hoover F5870-900 SteamVac Vacuum
Wheel is sticking. I want to remove the wheel to clean the axel. kenmore 116.27514700
Hi,\015\012\015\012Thanks for the clarification. This is actually fairly simple to remove the rear wheel, however as you'll see after this has been removed, there really is no axle attached to this. It just snaps into the main canister ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum