Having problems with your Kirby G10D Vacuum ?
HOW TO PUT BELT ON
\015 ROLLER BRUSH WILL NOT TURN BELT IS LOOSE\015
This is a video how to replace the delt on kirby
Repair Help & Product Troubleshooting for Kirby G10D Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of
Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?
The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums
My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn't have anything to hold the belt on. Is there supposed to be something holding the belt?
It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle. ... Dirt Devil CE6100 Featherlite Upright Vacuum
My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.
Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum
Got Dirt Devil Featherlite,keeps burning the belt out immediately and there is only one way to put the belt on...have put on 4 new belts.....what up?
Hi There,When a belt breaks immediately after installing it, this can ONLY mean one of two things. The first is that the belt was put back on incorrectly, and it may be pinched underneath of the beater bar. This would cause it to bre ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?
Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company. ... Hoover F6021-900 Steam Vacuum
We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.
I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums
Problem putting on flat drive belt on Hover Vaccun cleaner model # U6434-900. Also how do I get the belt on? Do you have tool to help put the belt on.
The best way is to use an flat blade screwdriver. Attach to motor first than but screwblade into belt holding it aginst the brush holder drum and roll the brush forward inching the rubber belt onto the spendle that drives the belt ... Vacuums
I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!
Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v
I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.
On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum
My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on
... Oreck XL Ultra Bagged Upright Vacuum
Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old
If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?
... Kenmore 34722 Grab-N-Go Upright Vacuum
Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.
I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.
I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t
It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums
The Belt on my Dirt Devil broke...so I purchased another belt and as soon as i put it on and started to vacuum it also broke, i noticed that the metal piece the belt goes on was extremely hot and was melting the belt. Whats wrong with it?
It may be that the beater brush is bound up . This will cause slipping, of the belt. Take out the brush and clean out the bushing . Hair gets wound up in side. once you have it cleand out. Put a few drops of cooking oil in side the bushing on both e ... Dirt Devil& Breeze Vision Canister Vacuum Vacuum
I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?
Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum
Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!
Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum
I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I put both belts on my U6634-900 and i can make brush spin manually, but the small belt looks to big, not fitting snugly and not turning brushes when i give it juice. Yes I have the right belts.
... Hoover U6634-900 WindTunnel Bagless Upright Vacuum
Belt drive keeps melting every belt we put on
Usually that means something is stopping the brushes from spinning weather it is not greased well or just something still there I can't tell you but that is the broblem. You could try asking in a vac store/repair if they've had a fair amount of that ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum