Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?
The toggle pedal you push to engage/disengage the wheels fell off
\015 I can here a part rattling around in the place where the pedal fell off; however, the fastener used is not your typical screw (i.e, cannot be taken off by a flathead or philips screwdriver). \015\012\015\012Is this a repair that I can perform at home?\015
The screw head is probably what's called a torx screw, and you can get torx screw drivers and sockets at the hardware store.
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The toggle pedal you push to engage/disengage the wheels fell off
The screw head is probably what's called a torx screw, and you can get torx screw drivers and sockets at the hardware store. ... Kirby Ultimate G Bagged Upright Vacuum
My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.
If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums
My Sentria always runs in the drive mode and it is so fast it seems out of control. If I push the neutral pedal it stays in drive. I can push it the regular way when it is turned off, whether the pedal is in the drive position or neutral.
I sold vacuums for almost 20 yrs and the Kirby gets lots of complaints. The transmission that it has in it breaks as your has and they are costly.The best thing to do would be to take the maching to the local vacuum store(eg. sewing and vacuum are of ... Kirby Ultimate G Bagged Upright Vacuum
Have a dirt devil breeze that the adjust. wheels fell off while replacing the beatter brush. can't figure out how to put the wheels back on
... Dirt Devil Breeze Bagless VacuumVacuum
Hello, I got a used Kirby Sentria. When I run the vaccum and push and pull on the handle, I can hearing a friction type noise. I got up close to the vaccum and it is not the wheels or roller. It is coming from the base of the handle. It's like it is pushing on something on the vaccum body and is creating the noise. Maybe transmission? Is this normal, or is it something I should be concerned about? Thanks for your help!
Try new belt yours may be slipping ... Kirby G5 Bagged Upright Vacuum
I have a 5260D Baby Lock Serger, which I had tuned up a year ago. I haven't used it very much since. When I took it in, and again now, it sews fine for awhile, then starts slowing down until it is barely sewing, even with the foot all the way down. The hand wheel seems very tight. - it doesn't turn freely, but takes a some push, like it is resisting a bit. Any idea what could cause this slow down and the tight hand wheel? I appreciate any ideas. Thank you. Maura
Hi,Since you say that you didn't use it for many years then does it make noise?If so it need oiling on its parts.oil orifice and point of contact.Please do rate the solution if the issue is resolved or post a comme ... Vacuums
My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.
It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I bought a fantom vacuum on HSN about 9 years ago.Whan it was delivered the first one was broken so they sent a second one.tThat one also was cracked on covering for brush. I called and they told me they were no longer available,so I kept that one,since it would cost me shipping to return.The back right side wheel evenually cracked and fell off.I was able to put it back on and it would stay for a few weeks or so.It now has a large piece of plastic that has broken off the wheel where the bolt fit
G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.
Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum
Wheels the wheels on my vacuum bunch up, have replaced them and still doing it, also it will not lock in an upright position, something fell off do not have part
The axle for the rear wheels have worn into the cut outs in the body that it goes through and they are rubbing on the wheel wells. This common for this vacuum model , the only real fix is to replace the body assembly. Sears will have to do this, this ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor
On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?
Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum
Front wheel fell off Ultimage G Kirby vacuum
... Kirby G6 Bagged Upright Vacuum
Wheel and lever fell off Kirby ultimate G
The spline shaft is probably worn. you will have to replace the assy. ... Kirby Ultimate G Bagged Upright Vacuum
My husband took the brush and base assembly apart to clean the unit...when he took the wheel assembly off the small white leveller inside fell off. How do we get this back on??
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
What pedal do you push to slant the start handle backwards
Hello,Here is a link to the owners manual.http://www.eureka.com/servlet/ListParts?model=4870&description ... Eureka Smartvac 4870 Bagged Upright Vacuum
Right wheel fell off.
I need more specific information. What brand and model of vacuum? Does it have a metal or plastic axle? ... Vacuums
My kenmore progressive vacuum handle release pedal fell off how can i fix this
... Kenmore 25512/ 25513 Progressive Canister Vacuum
The TechDrive fell out of my Kirby Ultimate G. This is the lever you step on to make the wheels move freely when vacuuming. How do you fix it?
... Kirby G5 Bagged Upright Vacuum
The height adjustment lever and left front wheel fell off my kirby g3 where does the spring go? do you have a schmatic?
... Kirby Ultimate G Bagged Upright Vacuum
Roomba 560 goes in small circles like it is in "spot mode". Wheels are clean and push up and down and turn easily.
This is the Circle Dance. Compare the behavior with the video on this site. You can also order a repair kit on the site as well. ... iRobot Roomba 560 Robotic Vacuum
Water not getting to cleaner head when pushing down the pedal. Cant find any blockage, motor sounds ok
Some times the tip /nasal git plugged from soap, it gets crystallized. can try running clean hot water in place of soap. Hope this helps please feel free to let us know if you would like more info. Thank you , Have a good day ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My foot pedal to my Bernina 930 broke last night. The plastic around the screws broke off so everything fell out... I have the pieces, but not sure how to put it back together. Can this be repaired.
Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.
I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My G6 kirby stopped working. i have checked the wire for fraying and continuity and found no problems. I have noticed that the foot pedal that turns the machine on doesn't seem to click when pushed on or off either. i have the motor exposed now to check if it is bad, but i am not sure how to pursue doing just that.
... Kirby G6 Bagged Upright Vacuum