Having problems with your Kirby Ultimate G Bagged Upright Vacuum ?
Vacuum does not run at all
\015 I have Kirby ulimate G and have disassembled the unit to the point of taking the motor out and the switch off of motor. I can not get any continuity on switch even if I short the two terminals extruding from switch and I don't know which terminals to check on motor. Motor does not smell shorted. Trying to determine if the problem is in the switch or the motor. Can you help?\015
It is most likely the switch if you are not getting any continuity to it. the switches on these units are designed to cut power to keep the motor from shorting out. you can get the power switch here for 28.99 less the shipping. http://www.kirbypartstore.com/kiswas.html
Repair Help & Product Troubleshooting for Kirby Ultimate G Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums
Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.
It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums
Fantom vacuum vacuum starts running fine at first,but after about 15 mins the suction stops but the vacuum continues to run
Sounds like a partly clogged filter ... Fantom Vacums FM741 Twister Bagless Upright Vacuum
DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.
... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum
On my Kenmore 36932 upright vacuum, the agitator continuously runs. It runs when the vacuum is turned off.
... Kenmore Vacuums
Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???
Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!
Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum
I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see
... Oreck XL Ultra Bagged Upright Vacuum
Vacuum won't run light comes on but vacuum doesnt
... Panasonic MC-V5745 Bagged Upright Vacuum
I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.
The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w
Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?
I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums
We have a Kenmore Progressive Model 116 Upright bagged vacuum with Hepa filter. It's at least a couple years old. For quite some time now when ever we use the vacuum the vacuum motor will shut off nafter about 5 min. of use. We then need to let it sit for awhile and then we can run it again for another 5 min. The bag has been change. Any one have any ideas how to fix this?
I suspect that you have a restriction. The motor sounds like the thermal break is stopping the motor before damage, due to heat.\012You must witness that the entire suction and discharge side are clear. This is not always very easy, but necessa ... Kenmore 34612 Bagged Upright Vacuum
We have had a Dyson DC14 for 5 years. Recently, when I run the vacuum, it whines a high pitch sound. It still maintains a suction and does not seem to have lost any power. I am unaware of anything that was done to change the condition of the vacuum. Concerned what the noise is and if it is damaging the vacuum.
... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I was vacuuming with an attachment, the vacuum began to loose suction and the hose collapsed, then the vacuum stopped running. I have turned it off and continue to plug it in off and on, using different plugs. It will not turn back on.
Hi there VacuumGuru for www.vacuumspot.com.au here. You have got yourself a blockage in the hose is all. The reason it wont turn on is because that machine has a thermal cut o ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Our vacuum will not stay running.. We have cleaned both filters several times since dyson told us there was a switch which turns the vacuum off if the filter in the ball was dirty, but we still need to keep pushing the switch several times to turn the unit back on while vacuuming.
... Dyson DC25 All Floors Bagless Upright Vacuum
I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums
I use the vacuum for cleaning up **** and **** from my dog now everytime i run the vacuum the whole house smells like **** what can i do to clean out the vacuum so it smells less
I am not surprised at all ... this is a very unhealthy procedure you are using ... endangering the health of everyone in your home ... particularly the family but not excluding visitors. Please stop this at once. You are sending all the stuff in th ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum
Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!
You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums
After using the vacuum for a while it would stop running. After sitting several hours it would run again. Now it won't run at all. It was just a couple of months old and I haven't been able to use it again. It was never used much and we paid good money for what has turned out to be a poor machine. Any suggestion?
... Dirt Devil M130000 ''i'' Dual Cyclonic Upright Vacuum Cleaner Vacuum
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you
Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums
Kirby vacuum I have a G 6 kirby vacuum. The power cord has been checked and has continutity and replaced the power switch and the vacuum will still not run
There are 2 safety switchs, one on the front that the nozzle activates, and one on the side that the bag asembly activates. The motor brushes and/or armature maybe bad. ... Kirby Ultimate G Bagged Upright Vacuum
The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?
Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum