Having problems with your Kirby Vacuums ?
HOW DO I REPLACE MY REAR WHEELS ON MY KIRBY G6...I WAS ABLE TO TAKE IT OFF BUT NOW WHEN I INSTALL ONE THE DRIVE SHAFT IS TOO SHORT TO INSTALL THE OTHERE???
Try equalizing the space between the two wheels and the drive shaft. If it's not equal, they may not fit properly, or at all.
Repair Help & Product Troubleshooting for Kirby Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
HOW DO I REPLACE MY REAR WHEELS ON MY KIRBY G6...I WAS ABLE TO TAKE IT OFF BUT NOW WHEN I INSTALL ONE THE DRIVE SHAFT IS TOO SHORT TO INSTALL THE OTHERE??? PLEASE HELP
Try equalizing the space between the two wheels and the drive shaft. If it's not equal, they may not fit properly, or at all. ... Kirby Vacuums
Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!
The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums
Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean
... Panasonic Vacuums
How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.
... RTO Vacuums
Hi, the seal from the impeller and pump shaft leaked. got new seal kit and installed. only disconnected the contacts piece to get clean attachment to shaft and the points now stay together looking like the springs are frozen thanks for your help
Hi ggetman38...\015\012\015\012That is normal\015\012What you are talking about is the centrifugal switch, they will swing apart when the motor rotates, they are there to start the motor with the points touching each other at motor ... Vacuums
Hi, this is our third Dyson DC-16.. the Trigger was shorting out on the first two.. Now we have the third one for about a year.. on charge when not using it.. don't use it every day, but for quick pickups only.. Just how long should the battery last? I was sent a new charger, didn't help.. it just won't hold the charge even tho two green lights are solid, but one red light does show up..
How are you charging your battery? Every battery has a memory. If you dont let it die the first come times then charge to full the battery will assume 40% is 100%. ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
This is crazy, as I've installed about a hundred ceiling fans in my day, but......what is the function of the 3rd pull chain on the Hampton Bay I just installed? It isn't the directional control as the fan has the traditional switch for this. The only thing I can figure is it's a means to control the fan and light with one pull chain. The generic instruction book doesn't address it. Thanks for your help!
Chain #1 = light on/off\012Chain #2 = direction of draft. up / down\012Chain #3 = Slow/med/fast speed control ... Vacuums
The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.
Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum
Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.
Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum
I am looking for spares for an Electrolux Nimbus multipurpose home cleaner (polisher/shampooer) the gear on the drive for the one brush has stripped. can you help me?
... Electrolux Vacuums
Fan belt wheel missing. Took it apart and discovered fan belt torn and no wheel on drive shaft for brush. I am assuming that there was one there originally.Did it shatter or what.What is solution. Can I get exploded view of this model or others like it.
Get another fan belt wheel of the model and place it over it ... Vacuums
I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher
If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums
Dyson dc04 drive belt keeps snapping have put 2 new ones on a made sure it was on shaft fully and brush did move before tunring on
... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum
Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa
Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum
The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]
This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum
I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the
Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
No manual Hi there my bissell will not **** up the water its been some time ago that I used it and it has not been used more than 2or 3 times can any one help me with this. I have also miss placed my manual and instruction this does not help me either .So if any one can help Id be a happy woman with clean floors thanx Vickie
Link to the manual download - http://www.bissell.com/Product_Search.aspx?Criteria=1699\015\012CHeck to see if the front of the unit is clogge ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I bought a Rival Ice Cream Maker, Model 8401 at a garage sale. Last week we were going to use it for the first time. When I opened the box I found that the Drive Shaft was missing. Everything else was there. Can I purchase a Drive Shaft for this machine from you?
Not from Fixya!Contact\015\012 rival here to order parts.\015\012\015\012http://www.rivalproducts.com/help.aspx?helpNav=3 ... Vacuums
Need help installing a pump belt on my bissel steam cleaner
... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.
HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum
Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?
HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums
I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks
Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums
I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1
As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum
Lost manual for emeril by t-fal bread machine model series bo1 or b01 can't really tell which number 0 or letter o.where can i find one most other products have an on line manual..i can t find one can u help me locate one..thanks
Hi - welcome to FixYa,\015\012\015\012Not easy to track these down and I can't find information relating to B01 or BO1, but I'm pretty sure this is the manual you're looking for:\015\012\015\012 ... Vacuums
Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet
Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum