Having problems with your singer 534 ?
why my upper thread is so tight and breaks
Sews and runs good just tight and upper thread breaks
Repair Help & Product Troubleshooting for singer 534
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.
I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums
The needle keeps breaking on my Janome J3-18 sewing machiene and the thread tension seems too tight. However the tension is set at 5 and it is standard thread and I'm using standard fabric. What's going wrong?
I have a janome BCC-30 sewing machine and the upper thread has started to break and fly out of the needle while I am sewing. The problem continues even when I change the tension dial.
I bought this machine about 3 years ago but hadn't used it due to illness. Now when I tried to sew with the Tuff Sew ,the threads continually break. If I can make about a 3 inch line of staight stitches without the top thread breaking,I consider myself fortunate The direction in the manual are extremely poor. I had to finish my project with my very old Bernina. I regret buying the Tuff Sew straight stitch. JLWebb
I do not have one but these machines require heavy duty thread...\015\012\015\012The manufacture recommends using only "#69 Bonded Nylon Thread"\015\012\015\012You should have a 18 to 20 gauge needle for that size threa ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
With my K6 Industrial Singer sewing machine the top thread seems to be too tight. The bottom thread is looping too much on the top of the fabric. The timming is ok. I have checked and rechecked that I have threaded it correctly. It was working great the other day. Please help as we are live out on a property and too far out to get someone out to look at it. Thanks Tania Sorry no category for sewing machines on your list
Hello there, loosen your top thread tension,if it looping on top of the material the tension is way too tight, you will also find changing the thread size to smaller thread, the top tension will also reduce,depending on application a good size thread ... Singer Vacuums
Upper thread of shark 803XC sewing machine will not pick up bobbin thread
I just had this machine delivered yesterday (Janome Magnolia 7330). When I sew a straight seam (all I've tried so far) I get loops at the underside of the fabric. I adjusted the upper thread tension, but that did not help. In fact the loops got larger as I increased the tension. My thought is that I don't have the machine threaded correctly. Thanks!
Your problem is in the tension adjustment. also check the stitch lengths. \012\012Kdog ... Vacuums
We have a vogue stitch janome model 539 115v sewing machine. we were trying to sew but, the thread is not picking up from the bobbin. the thread keeps breaking and we are unsure what tension setting should be used for cotton cloting. please help. thanks! tom staron
I have a Pfaff 7570 ... having a problem with the upper thread making a small loop just above the fabric by the eye of the needle, just before the tip of the needle is piercing the fabric, the stitches that produced are properly formed with the right tension, but the loops get in the way sometimes and I know it never used to do this before. After reading the service manual I'm suspecting the "thread check spring" is not functioning properly. The manual gives steps how to adjust it, but it d
Http://search-pdf-books.com/pfaff-creative-7570-sewing-machine-pdf/ ... Vacuums
I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me
Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums
Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther
Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
I bought a stitch & go sewing machine, the instructions for threading the machine are hard to read could you please explain or email a larger versin , specifically #3, 4, and 5 , i know i'm doing something wrong thread is breaking
My singer sewing machine how do I stop thread from breaking
A good sign when sewing is, when your thread keeps breaking, your needle usally has a spot on the tip and cuts your thread. If that doesn't solve it, it your timing in the machine. Also make sure your tension isn't too tight, that will also break yo ... Vacuums
Brother swing machine XL 5060 the upper or lower tension is always loose or tight .
I bought a used Nakajima 181L-2 sewing machine and I need a manual. I can't seem to get the tension right and it keeps breaking the thread when I try to sew heavier stuff like my horse blankets.
I have a janome sewing machine 432S, sounds like it needs to be oiled, but I don't know where, and it keeps breaking my thread at the needle
I need to replace upper thread holder of my bernina activa 145 S. I also need to know were I can purchase one at. thanks in advance
I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the
If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums
Have a White Jeans Machine, Heavy Duty, XL1760, one step buttonhole. Don't have a manuel and don't know how to thread, straight stitch. Its on A which it says zig zag, or straight. Also told it breaks needles.
Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.
Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How do i remove the old hose assembly non my simplicity 7350 so i can install the new part? It seems to be locked in tight, do i break the tabs?
Are you just trying to put the hose into the cuff? If so, you just need to know that the cuff is threaded so the wire of the hose fits in the threads. If you're asking about the assembly at the top of the hose--I don't know. Probably you have to take ... Simplicity 7250 Deluxe Vacuum
How do you get cover off dyson dco7 to replace electrical cord?...I can get the torx screw out, but the cover seems awfully tight and I don't want to break the cover
I would use a toilet plunger. ... Vacuums
Thread at needle breaks when sewing. - Vacuums
Most common problem is the quality of the thread, most sewing machines require quality thread or else it breaks especially if the material is thick or hard ... Vacuums
Remove Upper Body from Kenmore 116 25813508
... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum